Manual Bomann ES 184 CB (page 54 of 106) (English, German, Dutch, French, Italian, Polish, Spanish)

651949

Zoom out

Zoom in

1/106

WARNING: Danger of burns!

The water inside the container is hot.

13. You have now nished the bleeding process. Fill the water

tank to the MAX marking. Repeat points 6 through 12 twice

to clean the appliance on the inside. Let more water ow

through the steam nozzle. Now the appliance is ready to

use.

Making Espresso

1. Switch the appliance on. The status indicator lamp

lights

up. The appliance starts heating up. The warming plate (13)

heats up.

NOTE:

• Use the warming plate to pre-heat your cup(s).

• If you want to pre-heat the cup(s) more rapidly, rinse

them with hot water.

2. Make sure that the drip tray (6) and the drip tray grid (7) are

inserted.

3. Fill the water tank with the desired amount of clean, fresh

water. The water level must be between the MIN and MAX

markings. Close the lid again.

4. Select a lter insert (14/15). Place the insert in the lter

holder. Ensure that the lter safeguard is not upright.

5. Fill the lter insert with espresso grounds. Use the supplied

measuring spoon (18). Observe the MAX marking in the

lter insert. Spread the espresso grounds evenly and push

down slightly with the tamper (18). Clean the edge of the

lter holder.

6. Attach the lter holder to the group head. Ensure that the

lter holder is properly attached in the group head.

7. The necessary brewing temperature is reached as soon as

the indicator lamp

lights up. Place your pre-heated cup(s)

under the group head exactly on the two holes you can see

in the drip tray grid.

8. Press the push button to position. The hot water is

forced through the lter.

NOTE:

This process does not end automatically!

9. Stop the brewing process by turning off the pump when the

desired amount of espresso is in your cup(s): Press push

button (8) to

position.

10. Remove the cup(s).

NOTE:

Remove the lter holder every time after making

espresso. In this way you extend the lifetime of the group

head’s rubber seal.

11. Remove the lter holder from the group head.

12. Empty and rell the lter to brew another cup of espresso:

WARNING:

Metal parts of lter holder and lter insert are hot.

a) Flap the lter safeguard (17)

up. Push the lter safeguard

with your thumb towards

the lter insert while turning

the lter holder around (see

Fig.).

b) Tap the coffee grounds out of the lter insert. Use

a spoon, if necessary. Rinse the remaining coffee

grounds with hot water out of the lter insert.

13. To prepare the next cup/cups of espresso, proceed as

described above.

Making Cappuccino

Generally cappuccino consists of one-third coffee, one-third hot

milk and one-third frothed milk.

The milk froth should not be rm enough to be shaped with a

spoon. It should be creamy, such as not completely whipped

cream, of a viscous texture.

For the preparation you need in addition

• a larger, bellied cup (approx. 180 ml), in which you make

the espresso,

• a small frothing jug with spout (e.g. 0.3 l),

• a small, heat-resistant container,

• cold milk with at least 3.5% fat content.

To make cappuccino you rst have to make the espresso.

Follow the instructions under “Making Espresso” points 1

through 11.

Froth the milk as follows:

WARNING: Danger of scalding!

Escaping steam can cause injuries. During the heating

process hot steam/water can escape from group head and/or

steam nozzle!

• Ensure that the steam control knob (3) is set to “

” posi-

tion before activating the steam function.

• Do not direct the steam nozzle towards persons.

• Always place a container under the steam nozzle (4).

1. Ensure that push button (8) is in

position.

2. Swivel out the steam nozzle (4). Ensure that the steam

pipe is properly attached. Attach the steam nozzle cover all

the way on the steam nozzle.

3. Place a heat-resistant container under the steam nozzle.

4. Fill the jug half with cold milk.

5. Press push button (9) to

position. Wait until the indicator

lamp lights up.

6. Briey open the steam control knob (3) towards “ ” every

time before using the frothing function to drain collected

condensate. The appliance is ready to use if only steam

escapes.

7. Place your milk jug with the milk under the steam nozzle.

8. Lift the jug so that the steam nozzle sits just under the milk

surface.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bomann ES 184 CB in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 3,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bomann ES 184 CB Manual

Product: