379754

Bomann cb 594 Manual

20
Zoom out
Zoom in
Previous page
1/44
Next page
ENGLISH
20
Bread Baking Machine Functions
Buzzer function
The buzzer goes off:
• When pressing all the program keys;
• During the second kneading cycle of the NORMAL,
VOLLKORN, SCHNELL, KUCHEN and SANDWICH
programs to signal that the cereals, fruit, nuts or
other ingredients can be added.
• When the end of the program is reached.
During the warming phase at the end of the baking pro-
cedure the acoustic signal rings several times.
Repeat function
In case of a blackout the bread baking machine must be
started again. This is possible only if the program was
stopped before the kneading phase was reached. Other-
wise you will have to start from the beginning!
Safety functions
If the temperature of the appliance is still too high (more
than 40°C) for a new program after using the appliance
previously, H:HH will appear on the display when pres-
sing start again and an acoustic signal is given. If this is
the case, press the
START/STOPP key until the
H:HH message is deleted and the basic setting appears
on the display. Remove the container and wait until the
appliance has cooled.
The BACKEN program can be started immediately even
when the appliance is still hot.
Initial operation and program sequence
of the bread machine
Insert the baking tin
The nonstick baking tin must be held fi rmly with both
hands and be placed in the middle of the baking com-
partment. Press the tin downwards with caution until it
snaps into place. Insert the two kneading pegs on the
driving shafts.
Put in the ingredients
The ingredients must be put into the baking tin in the
order specifi ed in the relevant recipe.
Switch on
Insert the plug into a duly installed 230 V/50 Hz protec-
tive contact socket and switch on the appliance with the
on/off switch (L).
Select the program
1. Select the desired program with the
AUSWAHL
button.
2. If possible, select the desired level of browning.
3. If possible, select the desired quantity of dough.
4. With the
/ ZEIT buttons you can delay the start
of the program, if possible.
5. Press the
START/STOPP button.
Please note!
The programmes:
• NORMAL
• SCHNELL
• WEISSBROT
• SÜSSESBROT
• VOLLKORN
• TEIG
• SANDWICH
begin with preheating of the ingredients. During this time
the program is switched on without the dough hook mo-
ving. For further details please see the table „Sequences
of the Programmes“.
Mix and knead the dough
The bread baking machine mixes and kneads the auto-
matically until it reaches the right consistency.
Leave the dough to rise
After the last kneading cycle the bread baking machine
is heated to the optimal temperature for the rising of the
dough.
Baking
The bread baking machine sets the baking temperature
and time automatically. If the bread is too light at the
end of the baling program, use the BACKEN program to
let it brown more. To do so, press the
START/STOPP
key, then select the BACKEN program and start. When
the desired degree of baking has been reached, stop the
process.
Warming
Once the baking is over, the buzzer goes off to signal
that the bread or specialty can be removed. The 1-hour
warming time starts immediately.
End of the program phases
Switch off the appliance after use with the on/off switch
(L) and pull out the plug. At the end of the program pull
out the baking tin by using oven cloths, lay it on the
counter and if the bread does not fall out of the tin onto
the grid, move the knead shaft back and forth a few
times until the bread comes out. If one of the kneading
pegs is still stuck in the bread, take the hook supplied
with the appliance. Insert it under the warm loaf of bread
into the almost circular opening of the kneading peg and
wedge the hook against the lower edge of the kneading
peg preferably where the blade of the kneading peg is
located. You can then cut the bread easily and pull out
the kneading peg completely.
05-CB 594 D_GB_H Neu.indd 2005-CB 594 D_GB_H Neu.indd 20 10.01.2008 14:29:07 Uhr10.01.2008 14:29:07 Uhr
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann cb 594 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann cb 594 in the language / languages: English, German as an attachment in your email.

The manual is 1,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info