680440

Berner C500 Manual

28
Zoom out
Zoom in
Previous page
1/144
Next page
2.5 Safety instructions for fitting
The specialist carrying out the work must ensure that
installation is conducted in compliance with the prevailing
national job safety rules and regulations and those governing
the operation of electrical equipment. The relevant national
directives must be observed. Potential hazards as outlined in
DINEN13241-1 are avoided by construction and fitting
according to our guidelines.
After fitting has been completed, the installer of the gate
system must declare conformity with DINEN13241-1 in
accordance with the scope of application.
DANGER
Mains voltage
▶
See warning in section3.4
WARNING
Danger of injury due to unwanted gate travel
▶
See warning in section3.2
▶
See warning in section3.8
WARNING
Unsuitable fixing material
▶
See warning in section3.2.3
2.6 Safety instructions for initial start-up and for
operation
WARNING
Danger of injury during gate travel
▶
See warning in sections4 and 8
Danger of crushing and shearing
▶
See warning in sections4 and 8
CAUTION
Danger of injury due to the force value being set too
high
▶
See warning in section4.3.1
2.7 Safety instructions for using the hand
transmitter
WARNING
Danger of injury due to unwanted gate travel
▶
See warning in section6.1
CAUTION
Danger of injuries due to unintended gate travel
▶
See warning in section6
2.8 Approved safety equipment
Safety relevant functions or components of the control, such
as the force limit, external photocells and closing edge safety
device, have been designed and approved in accordance with
category2, PL"c" of ENISO13849-1:2008.
WARNING
Danger of injuries due to faulty safety equipment
▶
See warning in section4.6
2.8.1 Safety information on compliance with the
operating forces
If you observe these instructions, as well as the following
conditions, you can assume that the operating forces are
complied with according to DINEN12453:
• The centre of gravity for the gate must be in the centre of
the gate (maximum permissible deviation ±20%).
• The gate is easy to move and does not have any
gradients / slopes (0%).
• A sound-absorbing sealDP3 is fitted to the closing
edge(s). This must be ordered separately
(articleno.:436388).
• The operator is programmed for slow speed
(seesection4.3.2).
• The reversal limit at 50 mm opening width has been
checked and maintained over the entire length of the
main closing edge.
• The distance between the supporting rollers in self-
supporting gates (maximum width 6200mm, maximum
opening width 4000mm) is max. 2000mm.
3 Fitting
ATTENTION:
IMPORTANT INSTRUCTIONS FOR SAFE INSTALLATION.
OBSERVE ALL INSTRUCTIONS, INCORRECT FITTING
COULD RESULT IN SERIOUS INJURY.
3.1 Inspecting and preparing the gate / gate system
WARNING
Danger of injury due to a malfunction in the gate system
A malfunction in the gate system or an incorrectly aligned
gate can cause serious injury
▶
Do not use the gate system if repair or adjustment
work must be conducted.
▶
Check the entire gate system (joints, gate bearings and
fastenings) for wear and possible damage.
▶
Check for signs of rust, corrosion or fractures.
The sliding gate operator is not designed for operation with
sluggish gates, that is, gates that can no longer be opened or
closed manually, or can only be opened / closed manually
with difficulty.
The operator is only designed for use with gates that do not
have any gradient or slope.
The gate must be in a flawless mechanical condition, so that
it can be easily operated by hand (EN12604).
28
C300 - C800 / Rev. 1.1 RE / 07.2014
ENGLISH
… 28 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Berner C500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Berner C500 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 12,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info