Manual Berner C500 (page 26 of 144) (English, German, Dutch, French, Italian, Spanish)

680440

Zoom out

Zoom in

1/144

Dear Customer,

We are delighted that you have decided to choose a quality

product from our company.

1 About These Instructions

These instructions are original operating instructions as

outlined in the EC Directive2006 / 42 / EC. Read through all of

the instructions carefully, as they contain important

information about the product. Pay attention to and follow the

instructions provided, particularly the safety instructions and

warnings.

Keep these instructions in a safe place for later reference!

1.1 Further applicable documents

The following documents for safe handling and maintenance

must be provided:

• These instructions

• The enclosed test log book

• Sliding gate instructions

1.2 Warnings used

The general warning symbol indicates a danger that

can lead to injury or death. In the text, the general warning

symbol will be used in connection with the caution levels

described below. In the illustrated section, an additional

instruction refers back to the explanation in the text.

DANGER

Indicates a danger that leads directly to death or serious

injuries.

WARNING

Indicates a danger that can lead to death or serious injuries.

CAUTION

Indicates a danger that can lead to minor or moderate

injuries.

ATTENTION

Indicates a danger that can lead to damage or destruction

of the product.

1.3 Deﬁnitions used

Hold-open phase

Waiting phase at the OPEN end-of-travel position or partial

opening before the gate closes during automatic timed

closing.

Automatic timed closing

Automatic timed closing of the gate after a set time has

elapsed and after reaching the OPEN end-of-travel position or

partial opening.

DIL switches

Switches on the control circuit board for setting the control.

Through-trafﬁc photocell

When the gate is passed through, the photocell shortens the

hold-open phase and the gate closes a short time thereafter.

Impulse sequence control

With each push of the button, the gate is started against the

previous direction of travel, or the motion of the gate is

stopped.

Force training run

The forces necessary for gate travel are taught in during this

learning run.

Normal operation

Gate travel with the taught-in travel distances and forces.

Reference run

Gate travel towards the CLOSE end-of-travel position in order

to set the home position.

Reversing cycle / safety reversal

Gate travel in the opposite direction when the safety device or

force limit is activated.

Reversal limit

If a safety device is activated, gate travel is triggered in the

opposite direction (reverse cycle) up to the reversal limit

shortly before the CLOSE end-of-travel position. If this limit is

passed, no reversal occurs to ensure that the gate reaches

the end-of-travel position without disrupting travel.

Slow speed

The area in which the gate moves very slowly, in order to

gently move to the end-of-travel position.

Press-and-release operation

After an impulse is sent, the operator independently moves

into the end-of-travel position.

Partial opening

The distance the gate is opened for pedestrian trafﬁc.

Press-and-hold operation

The gate travels only as long as the respective buttons are

pressed.

Full opening

The travel to completely open the gate.

Pre-warning time

The time between the travel command (impulse) and the start

of travel.

Factory reset

Resetting the taught-in values to the delivery status / ex

factory setting.

1.4 Symbols used

Symbols

See text section

In this example, 2.2 means:

seetextsection, section2.2

Important note for avoiding damage to

property

C300 - C800 / Rev. 1.1 RE / 07.2014

ENGLISH

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Berner C500 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 12,56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Berner C500 Manual

Product: