680440

Berner C500 Manual

29
Zoom out
Zoom in
Previous page
1/144
Next page
▶
Check whether the gate can be opened and closed
correctly.
▶
Immobilize any mechanical locks not needed for power
operation of the sliding gate. This includes in particular
any locking mechanisms connected with the gate lock.
▶
Mechanically secure the gate to prevent it from running
out of its guides.
▶
Change to the illustrated section for the fitting and
initial operation. Observe the respective text section
when you are prompted to by the symbol for the text
reference.
3.2 Fitting the sliding gate operator
WARNING
Danger of injury due to unwanted gate travel
Incorrect assembly or handling of the operator may trigger
unwanted gate travel that may result in persons or objects
being trapped.
▶
Follow all the instructions provided in this manual.
3.2.1 Foundation
ATTENTION
Malfunctions in the connection cables
Malfunctions may occur if connection cables and supply
lines are ducted together.
▶
Duct the operator's connection cables (24VDC) in an
installation system that is separate from supply lines
(230 / 240VAC).
1. A foundation must be laid (see Figure1a / 1b). The
*
mark represents the frost-free depth (inGermany=
80cm).
A larger foundation must be laid if using a closing edge
safety device (see Figure1c / 1d).
2. Concrete ≥B25 / C25 (compacted) must be used with the
operator type with base plate.
3. A base foundation may be required for gates with inside
rollers.
4. The 230 / 240VAC mains lead must be routed through a
tube in the foundation. The lead to connect 24V
accessories must be installed in a tube that is separated
from the mains lead (see Figure1.1).
NOTE:
The foundation must have set and dried sufficiently before
the following work is carried out.
3.2.2 Establishing the fitting dimensions
1. Mark the drill position of the four drill holes on the surface
of the foundation.
Depending on the operator, use:
– The drill stencil at the back of these instructions for
Ø12mm holes with stock screws (see Figure2a).
– The base plate for Ø10mm holes with heavy-duty
anchors (see Figure2b).
2. Select the toothed track to be used from the table below
and find the minimum and maximum fitting dimensions
(dimensionA).
Toothed track Dimension A (mm)
Min. Max.
2901624 126 138
438631 125 129
438632 129 133
3.2.3 Fixing
▶
See Figures2a.1 / 2b.1
WARNING
Unsuitable fixing material
Use of unsuitable fixing material may mean that the
operator is insecurely attached and could come loose.
▶
Only use the provided fixing material in concrete
≥B25 / C25 (see Figures1.1 / 2.1).
ATTENTION
Damage caused by dirt
Drilling dust and chippings can lead to malfunctions.
▶
Cover the operator during drilling work.
▶
After drilling, check the depth of the hole.
Hole Depth
Ø12mm for stock screws 80 mm
Ø10mm for heavy-duty anchors 105 mm
▶
Use the socket wrench included in the scope of delivery
to install the stock screws.
3.2.4 Fitting the operator housing
▶
See Figures3 – 3.5
ATTENTION!
Damage due to moisture
▶
Protect the control from moisture when you open the
operator housing
▶
Open the operator housing, release the operator and
remove the circuit board bracket.
The motor and toothed wheel are lowered in the housing
when the operator is released.
▶
If necessary, cut the tube seals to fit the tubes.
▶
When the housing is placed on the stock screws or base
plate, pull the mains lead and, if necessary, the 24V
connecting lead from below through the tube seals and
into the housing without any distortion.
▶
When tightening, pay attention that it is horizontal, stable
and securely fastened.
3.3 Fitting the toothed track
Prior to fitting:
▶
Check that required hole depths are available.
▶
To fit the toothed tracks, use the connectors(bolts and
nuts, etc.) from the fitting accessories (see FigureC1 or
FigureC4). These must be ordered separately.
C300 - C800 / Rev. 1.1 RE / 07.2014 29
ENGLISH
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Berner C500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Berner C500 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 12,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info