577356
38
Zoom out
Zoom in
Previous page
1/71
Next page
01/ 2015
BENNING ST 725
29
- If R
PE
ishigherthantheadmissiblelimitingvalue(≤0.3Ωuptoalengthof5m)butlower
than 1 Ω, themeasuredvalue will bedisplayedwithout a rating, the“tAble”symbol will
appear on the display and the test procedure will be stopped. The responsible testing staff
determines by means of the limiting value table (see section 7.10 or the table on the rear
of the BENNING ST 725) and by means of the line length of the test object whether the
displayed measured value is acceptable or not.
Press the -key
2
to give the measured value a positive rating and a will be displayed
next to the R
PE
symbol. The test procedure will be continued.
Press the
-key
3
to give the measured value a negative rating and a
will be displayed
next to the R
PE
symbol. "FAIL" appears on the display to confirm that the measurement has
been stopped.
- If R
PE
is lower than the admissible limiting value, the measured value of R
PE
is shown and
a appears next to the R
PE
symbol. Now, the R
PE
measurement is carried out again with
reversed polarity and the highest measured value of both measurements will be displayed.
After the R
PE
test has been passed, the test of the insulating resistance is started.
- If "Lo LOAD" is shown on the display, please check whether the test object is switched on.
- Press the key
2
to continue the testing procedure in case of the load being too low (R
L-N
>
6kΩ).
- If "HIGH LOAD“ is shown on the display, this indicates an excessive load (R
L-N
<<14Ω,
I
LAST
(I
LOAD
) > 16 A) of the test object. There might be danger of a short-circuit or of an earth
fault. Check whether there is a short-circuit between the external conductor (L) and neutral
conductor (N) of the test object.
- If there is no short-circuit, you can continue with the testing procedure by pressing the key
2
.
- If the insulating resistance R
ISO
is higher than the admissible limiting value, a appears
next to the R
ISO
symbol.
BENNING ST 725 in mains operating mode:
- The BENNING ST 725 interrupts the testing procedure after the R
ISO
(insulating resistance)
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Benning ST 725 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Benning ST 725 in the language / languages: English, German, French as an attachment in your email.

The manual is 10,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info