577344
26
Zoom out
Zoom in
Previous page
1/202
Next page
03/ 2014
BENNING MM P3
18
7.6 Frequency ranges
Overload protection for frequency measurements: 600 V
eff
7.6.1 Frequency ranges for square wave signals (Switch setting: Hz, %)
Measuring
range
Resolution
Measuring accuracy for 5 V
SS
max.
(square wave signal)
Sensitivity
5 Hz 0.001 Hz ± (0.3 % of the measured value + 5 digits) > 1.0 V
ss
(rectangle)
50 Hz 0.01 Hz ± (0.3 % of the measured value + 5 digits) > 1.0 V
ss
(rectangle)
500 Hz 0.1 Hz ± (0.3 % of the measured value + 5 digits) > 1.0 V
ss
(rectangle)
5 kHz 1 Hz ± (0.3 % of the measured value + 5 digits) > 1.0 V
ss
(rectangle)
50 kHz 10 Hz ± (0.3 % of the measured value + 5 digits) > 1.0 V
ss
(rectangle)
500 kHz 100 Hz ± (0.3 % of the measured value + 5 digits) > 1.0 V
ss
(rectangle)
5 MHz 1 kHz ± (0.3 % of the measured value + 5 digits) > 1.0 V
ss
(rectangle)
7.6.2 Frequency indication for sinusoidal signals (Switch setting: V
AC
, Hz, %) and
actuation of the „SELECT“ key:
Measuring accuracy: ± (0.3 % + 5 digits) applies to sinusoidal voltages of up
to 600 V
eff
(10 Hz - 500 Hz) and displayed values in the AC voltage range
(V
AC
) higher than 50 % of the final measuring range value
7.7 Pulse duty ratio for square wave signals (Switch setting: Hz, %)
Overload protection in the case of pulse ratio measurement: 600 V
eff
Meas. range Resolution
Measuring accuracy up to 5 V
SS
(square wave signal, 5 Hz - 5 kHz)
Sensitivity
(30 % ≤ % ≤ 70 %)
0.1 % - 99.9 % 0.1 % ± (0.5 % of the measured value + 3 digits) > 1.0 V
ss
(rectangle)
8. Measuring with the BENNING MM P3
8.1 Preparing the measurement
Operate and store the BENNING MM P3 at the specied storage and operating tem-
peratures only! Do not permanently expose the device to sunlight.
- The connected black and red safety measuring leads comply with the valid provi-
sion, if they are undamaged.
- Please protect the connected black and red safety measuring leads against con-
tamination and damages!
- Check insulation of the safety measuring leads. If the insulation is damaged,
multimeter must be replaced immediately.
- Check the safety measuring leads for continuity. If the conductor in the safety
measuring lead is interrupted, replace the multimeter immediately.
- Before selecting another function by means of the rotary switch
7
, disconnect
the safety measuring leads from the measuring point.
-
Strong sources of interference in the vicinity of the BENNING MM P3
might involve
unstable readings and measuring errors.
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Benning MM P3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Benning MM P3 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish, Spanish, Norwegian as an attachment in your email.

The manual is 2,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info