577341
27
Zoom out
Zoom in
Previous page
1/169
Next page
18
- COM jack J
- jack for V, Ω, , Hz 9
- jack for the 10 A range K (BENNING MM 1-2/ 1-3)
of the BENNING MM 1-1/ 1-2/ 1-3 against ground is 1000 V.
Electrical danger!
Maximumcircuitvoltage for ameasuredcurrent of500V! In
caseoffusetriggeringatvaluesabove500V,damagesofthe
device might be involved. A damaged device might represent
an electrical hazard!
8.2.1 Voltage measurement
- Select the desired function (V AC) or (V DC) by means of the rotary switch
8 of the BENNING MM 1-1/ 1-2/ 1-3.
- Connect the black safety measuring lead to the COM jack J of the
BENNING MM 1-1/ 1-2/ 1-3.
- Connect the red safety measuring lead to the jack for V, Ω, , Hz 9 of the
BENNING MM 1-1/ 1-2/ 1-3.
- Bring the safety measuring leads into contact with the measuring
points and read the measured value on the digital display of the
BENNING MM 1-1/ 1-2/ 1-3.
See gure 2: DC voltage measurement
See gure 3: AC voltage measurement
8.2.2 Current measurement (BENNING MM 1-2/ 1-3)
- Select the desired range and function (A AC) or (A DC) by means of the
rotary switch 8 of the BENNING MM 1-2/ 1-3.
- Connect the black safety measuring lead to the COM jack J of the
BENNING MM 1-2/ 1-3.
- Connect the red safety measuring lead to the jack for the 10 A range K (DC
or AC currents up to 10 A) of the BENNING MM 1-2/ 1-3.
- Bring the safety measuring leads into contact with the measuring
points and read the measured value on the digital display of the
BENNING MM 1-2/ 1-3.
See gure 4: DC current measurement (BENNING MM 1-2/ 1-3)
See gure 5: AC current measurement (BENNING MM 1-2/ 1-3)
8.3 Resistance measurement
- Select the desired function (Ω) by means of the rotary switch 8 of the
BENNING MM 1-1/ 1-2/ 1-3
- Connect the black safety measuring lead to the COM jack J of the
BENNING MM 1-1/ 1-2/ 1-3.
- Connect the red safety measuring lead to the jack for V, , , Hz 9 of the
BENNING MM 1-1/ 1-2/ 1-3.
- Bring the safety measuring leads into contact with the measuring
points and read the measured value on the digital display of the
BENNING MM 1-1/ 1-2/ 1-3.
See gure 6: Resistance measurement
8.4 Diode test
- Select the desired function ( ) by means of the rotary switch 8 of the
BENNING MM 1-1/ 1-2/ 1-3.
- Connect the black safety measuring lead to the COM jack J of the
BENNING MM 1-1/ 1-2/ 1-3.
- Connect the red safety measuring lead to the jack for V, , , Hz 9 of the
BENNING MM 1-1/ 1-2/ 1-3.
- Bring the safety measuring leads into contact with the diode connec-
tions and read the measured value on the digital display of the
BENNING MM 1-1/ 1-2/ 1-3.
- For a standard Si diode applied in conduction direction, a conduction
voltage between 0.400 V and 0.900 V is displayed. „000“ indicates a short-
circuit inside the diode, „OL“ indicates an interruption inside the diode.
- For a diode applied in reverse direction, „OL“ is indicated. If the diode is
defective, „000“ or other values are indicated.
See gure 7: Diode test
8.5 Continuitytestwithbuzzer
- Select the desired function ( ) by means of the rotary switch 8 of the
BENNING MM 1-1/ 1-2/ 1-3.
- Connect the black safety measuring lead to the COM jack J of the
BENNING MM 1-1/ 1-2/ 1-3.
- Connect the red safety measuring lead to the jack for V, , , Hz 9 of the
09/ 2013
BENNING MM 1-1/ 1-2/ 1-3
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Benning MM 1.2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Benning MM 1.2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish, Spanish as an attachment in your email.

The manual is 12,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info