693646
27
Zoom out
Zoom in
Previous page
1/30
Next page
Overall wear of the
screw shaft.
Replace the screw shaft.*
transported into the
combustion chamber.
The turnstile chain was
damaged.
Replace the turnstile chain.*
Boiler fan cable is
disconnected (or
damaged).
Connect (or replace) the boiler fan cable.* Boiler fan does not
work.
The fan is damaged. Replace the boiler fan.*
The fan was clogged by
dust.
Clean the boiler fan.* The fan is noisy in
operation.
The fan bearings are
worn.
Replace the entire boiler fan.*
The fan does not rotate
during boiler
modulation at the
lowest output values.
The set values of the fan
speed are too low.
Increase the fan speed on the boiler
controller so as to guarantee its smooth
operation.
Water from the
emergency fire-fighting
equipment leaked into
the fuel feeder.
The fuel burnt through
to the fuel feeder, which
activated the
thermostatic valve.
Remove wet fuel from the feeder, fill the
container with new dry fuel and start-up the
boiler.
Water from the
emergency fire-fighting
equipment leaks into
the fuel feeder.
The thermostatic valve
on the feeder leaks.
Replace the thermostatic valve.
The boiler is filled with
wet fuel.
Refill the container with dry fuel. The walls of the fuel
tank are covered with
droplets of water.
The temperature in the
boiler room is low
(about 12 °C or less)
The boiler room requires a higher air
temperature (boiler room wall insulation,
installation of heating radiator to the boiler
room, etc.).
A short time passed
after firing in the boiler.
Let the boiler thoroughly flame up.
Fuel dosing is set to a
lower output.
Adjust the fuel dosing according to the
control unit instruction manual.
The boiler cannot reach
the rated output during
operation.
The boiler uses non-
prescribed fuel (high
humidity, lower calorific
capacity, etc.)
Refill the container with prescribed fuel.
The boiler is clogged
with soot.
Clean the heat transfer surfaces of the boiler
body.
The boiler is
overheating.
Reduce fuel dosage.
High chimney draft. Install a chimney flue draw limiter (this
activity must be performed by a specialized
company).
Ceramic reflector is not
installed in the boiler
body.
Install a ceramic reflector according to the
instruction manual.
The flue gas
temperature is higher
than specified in the
instructions.
The firing flap in the
boiler body is open.
Close the firing flap using the cleaner lever
and firing flap and secure it with a locking
screw with a plastic head.
Low chimney draft. Have a chimneysweeper check the value of
the chimney draft. If the measured value is
less than the value required (see
instructions), it is necessary to make
adjustments to the chimney.
Smoke appears in the
boiler room or fuel
container.
The boiler door and / or
the top cover of the
boiler body and / or the
fuel tank cover is not
closed properly.
Duly close the boiler door and / or the top
cover of the boiler body and / or the fuel tank
cover properly.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Benekov S100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Benekov S100 in the language / languages: English as an attachment in your email.

The manual is 1,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info