693646
26
Zoom out
Zoom in
Previous page
1/30
Next page
6.) A refractory ceramic reflector and ceramic plates are located above the boiler burner. They
do not require any special attention. Any fly ash deposited on the surface of the reflector
can be regularly removed, but it does not affect its function.
7.) For a reliable operation of the turnstile during fuel feeding into the screw feeder, it is
necessary to maintain proper tension of the chain, i.e. the deflection in the middle between
the sprockets must be in the range of 6 to 10 mm. If the deflection is bigger, the chain must
be replaced. When checking the tension and handling of the chain the boiler must be shut
down. Risk of hand injury!
8.) In case of a screw fuel feeder blockage its motor is protected against damage by the
thermal contact (working temperature of the fuel feeder motor is up to 85 °C), which after
exceeding the critical temperature shuts down both feeder motors and the fans. If this
happens, the boiler must be shut down and repaired.
NOTE: Before performing this operation it is necessary to make sure the boiler is
disconnected from the power supply (plug pulled out of the socket).
9.) Since pressurising occurs in the burner area during fan operation, it is necessary to ensure
perfect tightness of the boiler (boiler door, the top covers of the boiler body, etc.).
10.) Occasionally perform a visual check of the emergency fire-fighting equipment.
11.) In the event of an emergency (electricity outage for long periods, etc.) or if fuel burns
through the increase in temperature opens the thermostatic valve and any fuel is
extinguished with water from the water main.
Before restarting the boiler it is necessary to remove wet fuel, and fire the boiler in a
standard manner (see chap. 7.1.).
12.) The gearboxes are filled with synthetic oil in compliance with factory standards therefore
no further maintenance is required.
9. Troubleshooting
If you have problems with the operation of the boiler, try some of the following solutions:
SYMPTOM CAUSE SOLUTION
The boiler is not
connected to the mains.
Connect the boiler to the mains (400V/50Hz)
via power cord with plug.
The display does not
show any data.
Boiler controller failure. Replace the boiler controller.*
Boiler drive cable Is
disconnected (or
damaged).
Connect (or replace) the boiler drive cable.*
Boiler drive is damaged. Replace the boiler drive.*
Screw feeding device
does not work.
There was a motor
overheating and thus
the motor thermal
protection was
activated.
Let the motor cool, after cooling the motor
will restart automatically.
The fuel feeder contains
an obstacle (stone, etc.).
Demount the fuel feed screw and remove the
obstruction. Reassemble the feeder.*
The fuel contains a
substantial quantity of
dust.
Remove unsuitable fuel from the boiler, refill
the container with prescribed fuel.
Repeated activation of
the motor thermal
protection.
The alignment of the
drive, screw shaft and
burner is not correct.
Disassemble the fuel screw feeder, clean and
reassemble it with emphasis on ensuring the
alignment of the individual components.*
The screw shaft rotates,
though the fuel is not
The container does not
contain fuel.
Refill the container with prescribed fuel.
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Benekov S100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Benekov S100 in the language / languages: English as an attachment in your email.

The manual is 1,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info