589451

Batavia XXL SPEED SAW Mini BT-CS001 Manual

27
Zoom out
Zoom in
Previous page
1/64
Next page
27
EN
CLOCKWISE direction until the arbor screw is
removed. NOTE: The arbor screw has a left
hand thread. It must be turned CLOCKWISE
to be removed.
5. Remove the blade (4).
6.4 Select the correct blade
Before installing a blade into the tool, it is
important to select the correct blade for the type
of material being cut.
Warning! Using the incorrect blade
type can result in damage to the blade
and possible injury to the operator.
Carbide tipped blade
• 85 mm x 1.7 mm x 24 teeth
• Cuts aluminum, hardwood, laminates,
plastics
Super cut blade
• 85 mm x 1.0 mm x 80 teeth
• Cuts hardwood, soft wood, plastics
Diamond blade
• 85 mm x 1.8 mm
• Cuts ceramic and marble tile, circuit
boards, berglass reinforced plastics
Small Diamond blade
• 50 mm x 1.8 mm
• Cuts ceramic and marble tile, circuit
boards, berglass reinforced plastics
6.5 Install blade
Warning! Let hot hex nut cool before
attempting to change the blade.
1. Remove existing blade (if one is installed), arbor
screw and thick arbor washer as noted above.
2. Slide blade (5) into the tool so the hole in the
blade (6) slides over the arbor. NOTE: Make
sure the exposed teeth of a blade with teeth are
pointing forward.
3. Re-install thick arbor washer and arbor screw in
the reverse order in which they were removed.
4. Lock spindle using the spindle lock button and
tighten the arbor screw by turning it COUNTER
CLOCKWISE. NOTE: The arbor screw has a
left hand thread. It must be turned COUNTER
CLOCKWISE to be tightened.
5. Re-install blade guard in the reverse order in
which it were removed. NOTE: At this point you
must decide whether to install the universal
blade guard or the pipe cutting blade guard.
6.6 Adjust cutting depth
The cutting depth is controlled by limiting the amount
of blade exposed below the blade guard.
1. Loosen the depth control knob (1) by turning it
counter clockwise.
2. Slide it upward toward the handle (2) and
tighten the knob to hold the depth stop
mechanism in place.
3. Press the blade guard lock button (3) and
carefully pivot the blade guard (4) upward to
expose the amount of blade (5) to achieve the
desired depth of cut.
NOTES:
a) The measurement markings on side of the blade
guard (6) can be used as a guide in setting the
depth of cut. The measurement mark on the
guard that intersects with the edge of the blade
indicates roughly the depth of cut.
b) Always set the cutting depth 1/8" greater than the
thickness of the workpiece.
… 27 …


Need help? Post your question in this forum.

Forumrules
1

Forum

batavia-xxl-speed-saw-mini-bt-cs001

Reset search

  • I have a Batavia BT-CS001 XXL speed saw . Brilliant saw but one of the windings on the motor has gone open circuit . Can you supply a new replacement motor ? Submitted on 25-4-2020 at 13:49

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Batavia XXL SPEED SAW Mini BT-CS001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Batavia XXL SPEED SAW Mini BT-CS001 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Batavia XXL SPEED SAW Mini BT-CS001

Batavia XXL SPEED SAW Mini BT-CS001 Additional guide - English, German, Dutch, French - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info