Manual Batavia CROC SAW BT-JCS001 (page 31 of 64) (English, German, Dutch, French)

589480

Zoom out

Zoom in

1/64

BAR

GROOVE

CHAIN DRIVE

LINKS

Fig. 16

CHAIN

TENSIONING

SCREW

CHAIN

ROTATION

CHAIN

SPROCKET

Fig. 17

• Pull the frond handle all the way back and

depress the lower jaw lock button. Keep the

button depressed while releasing the

handle to lock the lower jaw in the open

position.

• Remove the chain cover bolt using the

combination wrench provided. Remove the

chain cover and set aside.

• Rotate the chain tensioning screw

counterclockwise as needed to release the

chain tension.

• Remove the bar and chain from the

mounting surface.

• Remove the old chain from the bar.

• Lay out the new saw chain in a loop and

straighten any kinks. The cutters should

face in the direction of chain rotation. If they

face backwards, turn the loop over.

• Place the chain drive links into the bar

groove as shown.

NOTE: Make certain of direction of chain

• Position the chain so there is a loop at the

back of the bar.

• While holding the chain in position on the

bar, reinsert the bar and chain through the

opening between the jaws and place the

loop around the sprocket.

• Fit the bar flush against the mounting

surface so that the bar stud is in the long

slot of the bar.

WARNING:

When placing the bar on the bar studs, ensure

that the chain tensioning pin is in the chain

tension pin hole. Failure to properly place the

chain tensioning pin in the chain tensioning pin

hole could cause the chain to come loose,

resulting in serious personal injury.

• Remove all slack from chain by turning the

chain tensioning screw clockwise, assuring

that the chain seats into the bar groove

during tensioning.

• Lift the tip of the bar up to check for sag.

Release the tip of the bar, and turn the

chain tensioning screw ½ turn clockwise.

Repeat this process until sag does not

exist.

• Chain is correctly tensioned when there is

no slack on the underside of the bar, the

chain is snug, but it can be turned by hand

without binding.

• Replace the chain cover. Reinstall the chain

cover bolt and tighten securely.

NOTE: If chain is too tight, it will not rotate.

Loosen the chain cover bolt slightly and

turn chain tensioning screw ¼ turn

counterclockwise. Lift the tip of the bar up

and retighten bolt. Ensure that the chain

will rotate without binding.

• Return the lower jaw to the closed position

by pulling back on the front handle and

allowing the handle to move all the way

forward.

Croc Saw Manual.indb 31 24-04-14 11:18

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Batavia CROC SAW BT-JCS001 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 16,88 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Batavia CROC SAW BT-JCS001 Manual

Product: