Manual Batavia CROC SAW BT-JCS001 (page 30 of 64) (English, German, Dutch, French)

589480

Zoom out

Zoom in

1/64

• Stop the motor and disconnect from power

supply.

• Pull the front handle all the way back and

depress the lower jaw lock button. Keep the

button depressed while releasing the

handle to lock the lower jaw in the open

position.

• Loosen the chain cover bolt to finger tight

using the combination wrench provided

then turn the chain tensioning screw

clockwise to tension the chain. Refer to

Replacing the Bar and Chain for

additional information.

NOTE: A cold chain is correctly tensioned

when there is no slack on the underside of

the guide bar, the chain is snug, but it can

be turned by hand without binding.

• Chain must be re-tensioned whenever the

flats on the drive links hang out of the bar

groove as shown in fig. 12

APPROX .050 in.

Fig. 13

Fig. 12

• During normal operation, the temperature

of the chain will increase. The drive links of

a correctly tensioned warm chain will hang

approximately . 050 in. out of the bar

groove, as shown in fig. 13

• Retighten the chain cover bolt securely.

• Return the lower jaw to the closed position

by pulling back on the front handle and

allowing the handle to move all the way

forward.

NOTE: New chain tends to stretch; check

chain tension frequently and tension as

required.

NOTICE:

Chain tensioned while warm, can be too tight

upon cooling. Check the “cold tension” before

next use.

REPLACING THE BAR AND CHAIN

See Figures 11-17.

WARNING:

To avoid possible serious injury, stop the motor

and disconnect from power supply before

replacing the bar, chain, or performing any

maintenance operation.

BAR

CHAIN

COVER

CHAIN COVER BOLT

CHAIN

Fig. 14

Fig. 15

CHAIN

TENSIONING

BAR STUD

SLOT

BOLT

CHAIN

TENSIONING

PIN HOLE

BAR

SPROCKET

CHAIN

COVER

Croc Saw Manual.indb 30 24-04-14 11:18

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Batavia CROC SAW BT-JCS001 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 16,88 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Batavia CROC SAW BT-JCS001 Manual

Product: