520774
20
Zoom out
Zoom in
Previous page
1/160
Next page
19
Upper and lower case door closed?
The case doors protect against touching the driven
parts in the inside of the saw.
Workplace tidied?
You may not start to operate the machine until you have
read these operating instructions, observed all the in-
structions given and installed the machine as described!
Before changing or adjusting the saw (i.e. replacing saw
band, inclining saw table, adjusting saw band coping etc.)
Switch off device
Wait for stop of the saw band
Pull out power plug
Also, note the following important points:
Wear protective clothing:
ear protection
safety goggles
protective mask
When sawing do not wear gloves, large clothes or jewels.
Danger of entering!
Take the correct working position. The saw teeth must
face the operator.
Take a position outside the danger zone of the saw band.
Never put into operation the machine when the doors pro-
tecting the saw band are open.
Put the hands plain with closed fingers on the work piece.
Saw only one work piece simultaneously. Never saw sev-
eral work pieces or individual items combined as packs
simultaneously. There is the risk that individual items can
be caught uncontrolled by the saw band.
Do not saw work pieces where cords, strings, bands, ca-
bles or wires are fixed. Danger of entering!
Press the work piece when sawing on the saw table.
Pay attention to that the work piece does not cant itself.
Do not slow down the saw band by lateral pressure.
L Use a work piece support plate so that when sawing
long work pieces these will not fall from the table after cut-
ting them through.
Never remove loose splinters, chips, or similar by hand.
At any case pay attention to all security advices.
Pushing stick
The pushing stick serves as enlargement of the hand
and protects against accidental touching of the saw band.
When do you have to use the pushing stick?
When the distance between saw band and parallel
stopper is less than 120 mm.
In case of straight cuts against the parallel stopper.
Hang in the pushing stick in case of non-use in the
mounting on the side of the device.
Do not use the pushing stick when it is damaged and
replace the pushing stick immediately.
23
Adjusting the upper saw band coping
The upper saw band coping protects against accidental
touching of the saw band and flying sawdust.
The height of the upper saw band coping must be adjusted:
Before sawing, to adapt to the work piece height
After changes of saw band (i.e. clamping or replacing saw
band, adjusting saw table)
The distance between saw band coping and work piece
must be 3 mm that there is a sufficient protection against
touching the saw band.
Adjusting:
1. Release fixation screw (H).
2. The required position of the saw band coping can be
adjusted with the adjusting wheel (18).
3. Refasten fixation screw (H).
Cutting round work pieces
Cutting round timber is not allowed with the standard feeding
assistances. When cutting round timber use a special device
which safes the work piece from skewing.
Edgewise cutting of plain work pieces
When sawing edgewise plain work pieces a suitable stop an-
gle for a safe guidance must be used.
Cutting narrow workpieces
(Width less than 120 mm)
Push the work piece with both hands forwards, within the saw
band zone use the pushing stick.
Cutting wide workpieces
With the flat of the hand and the fingers closed, push the work
piece to be cut along the stop.
Cutting long workpieces
Secure long workpieces against dropping down when
finishing the cutting process. Use roller supports or similar
devices for this purpose.
24
The sawing process
1. Select and adjust parallel stopper (14) and saw table
incline corresponding to the cutting type.
2. Select and adjust speed of saw band according to the
material.
When sawing with parallel stopper and inclined saw
table the work piece can cant. The parallel stopper must
therefore be fixed on the downwards inclined side of the
saw table.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika BSV315 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika BSV315 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish as an attachment in your email.

The manual is 2,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info