520774

Atika BSV315 Manual

21
Zoom out
Zoom in
Previous page
1/160
Next page
20
3. Adjust distance between saw band coping and work piece
to 3 mm.
4. Put work piece on the saw table.
5. Put in power plug.
6. Switch on saw.
7. Saw through work piece in one work step.
L Hint:
Make always a test cut to be able to correct the
adjustment.
8. Switch off saw when it is not intended to go on sawing.
Maintenance and cleaning
Before each maintenance and cleaning
work
− switch off device
− wait for stop of saw
− pull out power plug
Further maintenance and cleaning works than described in this
chapter shall only be carried out by the manufacturer or com-
panies named by the manufacturer.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.
Cleaning
L Observe the following to maintain the functionality of the
saw.
Do not wash down device with water.
Remove splints and sawdust only with a brush or vacuum
cleaner.
Clean and oil all moving parts regularly.
L Never use any grease!
Use for instance sewing machine oil, liquid hydraulic
fluid or environmentally acceptable spray oil.
Provide that the saw band stays rust-free and resin-free.
Remove all resin residues from the saw bench top.
L Resin residues can be removed with a commercial
maintenance and care spray.
Treat the surface of the saw table after cleaning with an
anti-blocking agent.
The saw band is a wearing part and becomes edgeless
after longer or more frequent use respectively.
Renew then the saw band.
Maintenance
Saw band exchange
Danger of cutting! Wear gloves when replacing the saw
band.
Only use suitable saw bands.
25 26
1. Open both case doors (2 / 7).
2. Release the 2 release handles (I) at the bottom side of
the guidance profile (26).
3. Take off the guidance profile (26).
27
4. Put upper saw band coping (19) completely down.
5. Put upper band roll (17) down.
° turn the adjusting wheel (1) anti-clockwise, the saw
band is relaxed
6. Take out saw band.
7. Put in new saw band.
L Pay attention to a correct position: the teeth must show
forward (direction door).
8. Put saw band centrally on the band roll (17).
9. Turn adjusting wheel (1) clockwise until the saw band does
not glide off any longer.
10. Fasten guidance gib and close lower case door.
11. Subsequently:
° Clamp saw band („Saw band tension“ p. 18)
° Adjust saw band („Incline of the upper band saw roll“ p.
18)
° Adjust band guidances („upper band guidance“ and
„lower band guidance“ p. 20)
° Keep saw running at least one minute for testing
° Switch off saw, pull out power plug and recheck
adjustments
Adjusting upper band guidance
The upper band guidance consists of:
° two guidance rolls (these guide the saw band laterally)
° a support roller (this supports the saw band from behind)
Check the guidance rolls and the support roller after
each saw band exchange and each saw band adjust-
ment and readjust it if necessary.
L Guidance rolls and support roller are wear parts. Check
these regularly and replace the rolls in case of wear at
the same time.
28
Adjust guidance rolls:
1. Release screws (J).
2. Adjust the holder (K) in that way, that the guidance rolls (L)
start always app. 1 mm behind the teeth ground.
3. Fasten screws (J).
29
4. Release screws (M).
5. Press guidance rolls (L) against the saw band.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika BSV315 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika BSV315 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish as an attachment in your email.

The manual is 2,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info