520774

Atika BSV315 Manual

18
Zoom out
Zoom in
Previous page
1/160
Next page
17
9
Fasten saw table with 4 nuts (M8) and washers at the saw
table guidance (20).
10
Adjust saw table
Angle the saw table (13) laterally.
Î Release the four fixation screws (C).
Î Angle saw table (13) in a way that the saw band is located
in the centre of the table insert.
Î Refasten attachment screws (C).
11
Angle the saw table (13) rectangularly
Î Place upper saw band coping completely upwards (see
„Adjustment of the upper saw band coping” p. 19)
Î Check saw band tension (see „Saw band tension“ p. 18)
Î Release fixation screw (D).
Î Angle the saw table with the help of an angle rectangular to
the saw band.
Î Refasten fixation screw (D).
12
Release the counter nut (E) and adjust the adjusting screw (F)
until the adjusting screw touches the saw table. Refasten the
counter nut.
13
Assemble parallel stopper
Assemble stopper guidance profile (26)
Push the stopper guidance profile (26) on the table top and
fasten the wing screws.
14
You can assemble the parallel stopper (14) on the right or left
side of the saw band.
Push the parallel stopper (14) on the stopper guidance profile
(26) and fasten it like pictured.
15
Mount the holder (3) for the pushing stick.
Preparing for startup
L
To obtain a perfect working of the machine follow the
following advices:
Place the saw in a place that fulfils the following conditions:
− secured against slipping
− free of vibrations
− even
− free of tripping hazards
− adequate light
Before each use, check
− Connection cables for defects (cracks, cuts, etc.)
Do not use any defective cables.
− the table insert for its proper condition
− the saw band for its faultless condition
− that all doors are closed
− whether the pushstick is to hand
Do not use any deformed or damaged saw bands.
Replace a worn-out or damaged table insert immediately.
When the machine is not used open-air it must be con-
nected on both suction sockets with a splinter extraction
system (i.e. portable small dust extractor).
Start-up
L Electric supply
Compare the voltage listed on the machine’s type plate, e.g.
230 V, with the mains voltage and connect the machine to a
suited and and properly earthed electrical socket.
L AC-motor
Use an electrical socket with a rated voltage of 230 V with a
fault-current circuit breaker (30 mA).
L Main fuse: 10 A slow
Use an connecting or extension cable in compliance with IEC
60245 (H 07 RN-F) having a core cross-section of at least:
1.5 mm² for cable lengths up to 25 m
2.5 mm² for cable lengths over 25 m
16
ON/OFF switch
Do not use any device where the switch can not be swit-
ched on and off. Damaged switches must be repaired or
replaced immediately by the customer service.
Switching on
Press the green button ( I ) on switch.
L Restart protection in case of power failure
The device cuts off automatically in case of power failure. To
restart, first push the red button ( 0 ) and then the green button
( I ).
Switching off
Press the red button ( 0 ) on switch.
Saw band selection
The saw band delivered by standard is suitable for wood and
most plastics.
Consider when selecting the saw band,
− that no edgeless or damaged saw bands are used.
− that the selection of the saw band and the number of revo-
lutions is suitable for the material to be cut.
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika BSV315 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika BSV315 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish as an attachment in your email.

The manual is 2,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info