475724
25
Zoom out
Zoom in
Previous page
1/135
Next page
25
Â
Release the chain brake. Push the front hand guard
towards the front handle (3)
. The chain saw is ready
for operation.
Only operate the throttle trigger (6) with the chain
brake released. A blocked saw chain may result in
damages to the chain drive.
To saw simultaneously operate the throttle lock-out
switch (5) and the throttle trigger (6).
L If you release the throttle trigger, the saw chain will
stop and the engine will idle. If the saw chain runs in spite
of non-pressed throttle trigger, you have to adjust the idle
speed. (Â “Maintenance”)
Stopping the engine
 Release the throttle trigger (6)
Put the toggle switch (8) to its bottom position.
Starting with warm engine
Start the chain saw as described under “Starting with cold
engine”, but leave the choke lever in its operating position.
W
W
a
a
r
r
t
t
u
u
n
n
g
g
u
u
n
n
d
d
R
R
e
e
i
i
n
n
i
i
g
g
u
u
n
n
g
g
Before each maintenance and cleaning work
Stop the engine.
wait for stop of chain saw
Remove the spark plug connector.
Wear protective gloves in order to avoid injury
to the hands.
Do not carry out maintenance work close to
open flames.
Risk of fire.
Maintenance and repair work other than those described in this
chapter is only allowed to be carried out by service staff.
Use only original parts.
Other parts can result in unexpected
damages and injuries.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Maintenance
To guarantee a long and reliable usage of the chain saws carry
out the following maintenance works regularly. Â Maintenance
and cleaning schedule.
Check the chain saw for obvious defects such as:
loose or damaged saw chain
loose fastenings
wear, especially chain, guide bar and chain wheel
worn or damaged components
leaks from the fuel/oil tank cap or fuel lines
correctly assembled and faultless covers and protective
devices.
Necessary repair works or maintenance works have to be
carried out before the usage of the chain saw.
Adjusting the chain lubrication
Stop the engine!
The chain lubrication is factory-set. Depending on the type of
wood and working techniques the amount of oil may vary and
has to be corrected.
Â
Adjust the chain lubrication using the
adjusting screw (12) which is located
below the product.
Anticlockwise turning M large amount of oil (MAX)
Clockwise turning M small amount of oil (MIN)
L The chain lubrication is correctly adjusted when the
saw chain throws off small amounts of oil during
operation.
Saw chain and guide bar
Saw chain and guide bar are exposed to a great extent of
wearing. Replace the chain saw and the guide bar without any
delay if their proper function is no longer ensured. Â “Installing
the guide bar and the chain saw”.
Sharpening of saw chain
You can only work safely and well with a sharp
and clean saw chain. Damaged or incorrectly
sharpened saw chains increase the risk of
kickbacks.
The saw chain has to be sharpened if
½ only wood dust is thrown out instead of shavings
½ you have to press the chain saw through the wood during
cutting
L Inexperienced users: Have the saw chain sharpened by a
specialist/service workshop.
If you sharpen the saw chain by yourself, note the values below
and use the supplied round file. (Additional accessories are
available from specialist shops.)
Saw chain type Carlton K2L-BL
Round file 3/16“ (Ø 4,8 mm)
Depth gauge distance T .028“ (,71 mm)
Schärfwinkel α 35°
Breast angle β 60°
Planing tooth length a min. 3 mm
 Firmly clamp the chain saw's guide bar in a vice and
block the saw chain. Apply the chain brake
.
Â
To advance the saw chain release the chain brake.
Â
Use the supplied round file (37) to file all sharpening
angles (α=35°).
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika BKS 45 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika BKS 45 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 2,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info