475724
26
Zoom out
Zoom in
Previous page
1/135
Next page
26
LDo only apply 2-3 strokes with the file.
L The sharpening angles must be identical. Unequal
sharpening angles result in an erratic chain run or chain
breaking.
Â
While sharpening keep the file at an angle of 10° to the
guide bar.
 Using the round file and the correct sharpening angle the
correct breast angle β will result.
Â
The planing tooth lengthes (a) must be equal. Unequal
lengthes may lead to erratic chain run or chain breaking.
Â
Once all sharpening angles are filed your saw chain is
sharp, but it will possibly not cut. There must be always
a depth gauge distance (T = distance between depth
gauge and cutting edge).
L Use a flat file to file the depth gauge distance.
Be sure to chamfer the leading edge of your depth
limiter with a file. The original shape of the cutting link
must be preserved.
L Only remove a little amount of material when
sharpening.
You can also sharpen your saw chain yourself by using our
electric sharpener KSG 220 (article-no.: 302360).
Cleaning of guide bar
 / Â
Check and clean the oil outlets (A) of the guide bar and the
guiding groove (B) on a regular basis.
Remove any burr using a flat file.
Turn round the guide bar after each chain exchange /
sharpening to avoid single-side wearing.
L Immediately replace a damaged guide bar.
Chain wheel
The demand of the chain wheel is particularly great. Check
regularly the teeth of the chain wheel for wear or damages.
Â
Clean the chain wheel (18) and the guide bar fixing
device using a brush.
L A worn or damaged chain wheel reduces the durability
of the saw chain and should therefore immediately be
exchanged by the customer service.
Cleaning the air filter
Clean the air filter from dust and dirt on a regular basis to
prevent
- starting problems,
- loss of output,
- too high fuel consumption.
Clean the air filter every 8 operating hours, or more frequently in
dusty environments.
Â
1. Open the air filter cover (21).
2. Pull off the air filter cover (28).
3. Remove the air filter (22).
4. Cover the intake opening with a clean cloth to prevent dirt
from coming into the carburettor.
5. Pull apart the both parts of the air filter.
6. Wash the air filter in a luke warm soapy solution.
Do not puff/blow out dirt particles, otherwise there is a
risk of eye injury.
7. Allow the air filter to dry well and reinsert it.
L Damaged air filters must be replaced without
delay.
Checking / Replacing the fuel filter
Â
The chain saw is equipped with a fuel filter. Check it regularly
and clean or replace it if required.
For this open the tank cap (9) and pull out the fuel filter (10).
If the filter is only slightly contaminated, carefully pull it from the
oil line and clean it using petroleum ether.
L If it shows a great extent of contamination, replace the
fuel filter.
Checking / Replacing the spark plug
- Do not touch the spark plug or the spark plug
connector while the engine is running. High voltage!
- Risk of burning on the hot engine.
- Wear protective gloves.
Check the spark plug and the spark gap on a regular basis.
For this proceed as follows:
Â
Open the air filter cover (21).
Â
Pull the spark plug connector (23) from the spark plug
(24). Remove the spark plug using the supplied wrench
(36).
Â
The spark gap must be 0.6 to 0.7 mm.
Clean the spark plug when it is contaminated.
Install the spark plug in reverse order.
Do not overtighten the spark plug.
Replace the spark plug:
- every 100 hours or once in a year (whichever case comes
first)
- when the insulating body is damaged,
- when the electrodes show excessive erosion,
- when the electrodes show excessive dirt or oil.
Use the following spark plug type: NGK-BPMR7A
BOSCH WSR6F
OREGON OPR15Y
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika BKS 45 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika BKS 45 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 2,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info