736695

AS Motor AS 940 Sherpa 4 WD RC Manual

41
Zoom out
Zoom in
Previous page
1/60
Next page
Maintenance
41
Checking when the engine is running
1. Start the engine.
ð The device must be stopped.
2. Pull the accelerator lever all the way up.
ð The engine is idling.
3. Repeat the test procedures for steering, drive lever and
cutting height.
ð Function is as described in the respective point.
ð The device must drive forward when you press the
right joystick forward.
ð The device must drive backwards when you press the
right joystick backwards.
ð The device must stop without delay when you press
the right joystick backwards.
Checking the safety functions
Magnetic contact switch on the transmitter holder
1. Select the operating mode MC.
2. Sit down on the driver’s seat.
3. Switch on the transmitter and the receiver.
4. Start the engine.
5. Turn the accelerator lever to neutral position.
6. Remove the transmitter from the transmitter holder.
7. Turn the accelerator lever forward to slow speed.
ð The engine must stop.
Seat contact switch
1. Select the operating mode MC.
2. Insert the transmitter into the transmitter holder.
3. Sit down on the driver’s seat.
4. Switch on the transmitter and the receiver.
5. Start the engine.
6. Turn the accelerator lever forward to slow speed.
7. Carefully relieve the driver’s seat.
ð The engine must stop.
Magnetic contact switch on the transmitter holder
and seat contact switch
1. Select the operating mode MC.
2. Insert the transmitter into the transmitter holder.
3. Sit down on the driver’s seat.
4. Switch on the transmitter and the receiver.
5. Start the engine.
6. Turn the accelerator lever forward to slow speed.
ð The motor must not be stopped.
Checking the Emergency stop switch
1. Select the operating mode MC.
2. Sit down on the driver’s seat.
3. Switch on the transmitter and the receiver.
4. Start the engine.
5. Move on a terrain where the blade can rotate freely and
does not touch objects or the ground.
6. Make sure that nobody is in the danger area of the device.
7. Engage the blade.
8. Press the Emergency stop switch on the device.
ð The blade must come to a standstill from full speed in
less than 5 seconds.
ð The engine must stop.
ð The status indicators on the device must be perman-
ently lit.
Checking the start-stop switch with key
1. Select the operating mode RC.
2. Switch on the transmitter and the receiver.
3. Start the engine.
4. Drive on large, open and level terrain.
5. Make sure that nobody is in the danger area of the device.
6. Drive slowly forward.
7. Press the start-stop switch.
ð The accelerator lever must go to neutral position/parking
brake.
ð The engine must stop.
ð The status indicators on the device must be permanently
lit.
Checking the key function
1. Press the start-stop switch.
2. Remove the key from the start-stop switch without turning
it.
3. Try to switch on the transmitter.
ð Without key the transmitter it must be impossible to turn
on the transmitter.
Checking the transport position of the
blade
1. Select the operating mode MC.
2. Sit down on the driver’s seat.
3. Switch on the transmitter and the receiver.
4. Start the engine.
5. Move on a terrain where the blade can rotate freely and
does not touch objects or the ground.
6. Make sure that nobody is in the danger area of the device.
7. Move blade to transport position.
ð Now the blade should not engage.
… 41 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AS Motor AS 940 Sherpa 4 WD RC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AS Motor AS 940 Sherpa 4 WD RC in the language / languages: English as an attachment in your email.

The manual is 2,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of AS Motor AS 940 Sherpa 4 WD RC

AS Motor AS 940 Sherpa 4 WD RC User Manual - German - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info