736695
43
Zoom out
Zoom in
Previous page
1/60
Next page
Maintenance
43
Changing the blade
1 1
1
1
2
2
3
3
4
6
55
Fig.31:
Cutting blades(5)
The cutting blades should move easily. To ensure this, al-
ways keep the pivotal point (3) clean. Never mow when the
cutting blades are stuck.
Caution! To prevent unbalance replace or reverse the cutting
blades in pairs only!
The cutting blades are reversing blades. Reverse both cutting
blades
when one of the wear marks(1) was reached.
when the second cutting edge of the cutting blade has not
been used yet.
It is absolutely necessary to change the cutting blades and
the fastening parts
when one of the wear marks(1) of the second cutting edge
was reached.
when the thickness of the cutting blade at any point is be-
low 1 mm (exception: cutting edge).
Mulching blade(6)
The mulching blade and the fastening parts must be changed
when one of the wear marks (1) was reached.
when the thickness of the blade at the rear edge(2) or at
any other point is below 1mm (exception: cutting edge).
Original blade
An original AS-blade is engraved with:
AS XXXXXXXX
The engraving shows the spare part number.
Checking the condition of the cutting blade screws
Warning
When a screw head is worn, the cutting blades can be-
come loose.
► Check all screws used for fastening the cutting blades!
Fig.32:
The screw head (3) wears off during mowing and must be re-
placed at the latest when it is down to a thickness of 2 mm.
To prevent unbalance replace the cutting blade screws in
pairs only!
Checking the blade clutch
1. Select the operating mode MC.
2. Sit down on the driver’s seat.
3. Switch on the transmitter and the receiver.
4. Start the engine.
5. Move on a terrain where the blade can rotate freely and
does not touch objects or the ground.
6. Make sure that nobody is in the danger area of the device.
7. Engage the blade.
8. Disengage the blade.
ð The blade must come to a standstill from full speed in
less than 5 seconds.
ð The status indicators on the device must go out.
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AS Motor AS 940 Sherpa 4 WD RC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AS Motor AS 940 Sherpa 4 WD RC in the language / languages: English as an attachment in your email.

The manual is 2,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of AS Motor AS 940 Sherpa 4 WD RC

AS Motor AS 940 Sherpa 4 WD RC User Manual - German - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info