736695

AS Motor AS 940 Sherpa 4 WD RC Manual

40
Zoom out
Zoom in
Previous page
1/60
Next page
Maintenance
40
Cleaning the device
After each use, you should clean the device thoroughly, es-
pecially the bottom side and the blade.
Stuck grass or dirt affect the grass discharge and the cutting
quality. For a sufficient engine cooling, keep the engine
cover, ventilation grid, and the engine clean.
For sufficient cooling of the hydrostat transmission, keep the
gearbox casing and the area around the gearbox fan clean.
Fire hazard!Pay special attention so that components on the
silencer are clean.
For cleaning use a hand brush. Remove stubborn soiling with
a wooden or plastic spatula. Clean the outer housing parts
with a cloth.
Do not rinse off the device with a water jet or high pressure
cleaner! Do not use aggressive cleaning agents.
General inspection
To make sure that the device can be operated safely, check
all nuts, bolts, screws, connection of fuel lines, air filters etc.
regularly for firm seating. Check the ignition wire and the
spark plug connectors for damage.
Immediately replace damaged or worn parts, especially cov-
ers, protection skirt, silencers or fuel tank (authorised service
centre).
Check all parts that that contain fluids for leaks and proper
condition. These can be: Fuel tank, fuel valve, fuel lines, car-
buretor, engine, gears, battery, hydraulic system.
In case of leaks, contact an authorised service centre.
Check the safety switches for proper function. It must not be
possible to start the engine when:
– there is no driver on the driver’s seat.
– The blade clutch is switched on.
– The lever for the cutting height adjustment is not in trans-
port position.
– The drive lever is not in neutral position.
If the engine is running and the driver leaves the seat, the en-
gine must shut down.
Contact an authorised service centre if one of these condi-
tions is not met.
Checking the safety functions
Check the safety switches for proper function. It must not be
possible to start the engine when:
– The driver does not sit on driver’s seat.
– The blade clutch is switched on.
– The lever for the cutting height adjustment is not in trans-
port position.
– The drive lever is not in neutral position.
If the engine is running and the driver leaves the seat, the en-
gine must shut down.
Checking the RC functions
Checking when the engine is not running
1. Set the selector lever operating modes on the rear of the
device to RC mode (remote control mode).
2. Switch on the transmitter and the receiver.
3. Set the toggle switch “Steering direction reversal” to nor-
mal position.
Checking the steering
1. Press the right joystick to the left.
ð Steering steers to the left without delay.
2. Release the right joystick.
ð The steering moves to the middle position without
delay.
3. Press the right joystick to the right.
ð Steering steers to the right without delay.
4. Release the right joystick.
ð The steering moves to the middle position without
delay.
Checking the drive lever
1. Set the rotary knob “maximum driving speed” to the rabbit.
2. Press the left joystick forward.
ð The drive lever moves forward without delay.
3. Release the left joystick.
ð The drive lever moves to neutral position/parking
brake without delay.
4. Press the left joystick backwards.
ð The drive lever moves backwards without delay.
5. Release the left joystick.
ð The drive lever moves to neutral position/parking
brake without delay.
Checking the cutting height
1. Press the toggle switch “Lower cutting height” backwards
until the cutting height adjustment stops by itself.
ð The cutting height display must be set to 1.
2. Press the toggle switch “Higher cutting height” forward un-
til the cutting height adjustment stops by itself.
ð The cutting height display must be set to 5.
3. Briefly press the button “Transport position blade”.
ð The blade is moved to transport position.
ð The cutting height display must be set to 0.
4. Briefly press the toggle switch “Lower cutting height”.
ð The cutting height moves independently from trans-
port position to the highest cutting height.
ð The cutting height display must be set to 5.
… 40 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AS Motor AS 940 Sherpa 4 WD RC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AS Motor AS 940 Sherpa 4 WD RC in the language / languages: English as an attachment in your email.

The manual is 2,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of AS Motor AS 940 Sherpa 4 WD RC

AS Motor AS 940 Sherpa 4 WD RC User Manual - German - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info