578744
9
Zoom out
Zoom in
Previous page
1/17
Next page
E-9
English
Single wiring
e A28 is designed for bi-wiring, which is why there are duplicate speaker terminals on the back. For
single wiring, we recommend that you use the lower set of speaker terminals on your amplier. If each
speaker has more than one pair of connecting terminals, use the terminals labelled LF or ‘Low Frequency’
for each speaker.
Connect the positive terminal of the right speaker connection on the amplier (coloured red and labelled
+R) to the positive terminal of your right speaker. Similarly, connect the negative terminal of the amplier
(coloured black and labelled with R) to the negative terminal of your speaker. Repeat the process for the le
speaker, using the amplier terminals labelled +L and L.
If your speakers support bi-wiring, then there is a strip of conductive metal on the speakers connecting the
low-frequency terminals to those for the higher-frequencies; this MUST NOT BE REMOVED in a single-
wired system.
Bi-wiring
Bi-wiring is performed in the same way as single wiring except that, for each speaker, a pair of cables are
used to connect the amplier to each speaker.
Follow the instructions given for single wiring; then perform the same actions, this time connecting the
upper set of speaker terminals on your amplier to the terminals labelled HF or ‘High Frequency’ for each
speaker. Please refer to the illustration.
Speakers that support bi-wiring have a strip of metal on the speakers connecting the low-frequency
terminals to those for the higher-frequencies; this MUST BE REMOVED in a bi-wired system.
Bi-amping
Bi-amping requires the use of two ampliers per channel. Normally, your A28 is used to drive the high-
frequency (treble) speakers, while a power-amplier (such as a P38) is used for the lower (bass) frequencies.
Connect your A28 to the speakers as described for single wiring, with the exception that the A28 should be
connected to the speaker terminals labelled HF or ‘High Frequency’. en connect the power amplier (P38,
for example) to the LF or ‘Low Frequency’ terminals, as in the diagram. A pair of audio interconnect cables
are also required to connect the pre-amp outputs of the A28 to the power amp inputs of the P38.
Note that the strip of metal on the speakers connecting the lower terminals to the upper terminals MUST
BE REMOVED. Failure to do so will result in damage to both ampliers, which will not normally be
covered under warranty.
An A28 connected to speakers using single wiring


An A28 connected to speakers using bi‑wiring


An A28 and P38 connected to speakers using bi‑amping



9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam A28 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam A28 in the language / languages: English as an attachment in your email.

The manual is 0,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Arcam A28

Arcam A28 User Manual - German - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info