578744

Arcam A28 Manual

7
Zoom out
Zoom in
Previous page
1/17
Next page
E-7
English
Pre-/power-amplifier connections
PRE OUT
To use your A28 as a dedicated pre-amplier, or as part
of a bi-amp’ed system, connect the PRE OUT sockets to
the input sockets of your power amplier.
Recording loop
e A28 is equipped with a recording loop, for use with
recording devices (such as a CD recorder, DAT recorder,
cassette recorder, VCR, PVR etc.).
AV RECORD OUT
Connect these output sockets to the input sockets of
your recording device (usually labelled RECORD or IN).
AV PLAY IN
Connect the output sockets of your recording device
(usually labelled P LAY or OUT) to these inputs.
If you do not have a recording device, you can use this
input for other (line-level) equipment, such as a TV,
DVD, CD player, radio tuner, PVR, etc.
Audio inputs
Although the inputs are labelled for specic devices, all
have the same characteristics and each may be used with
any line-level product. e exception is the Phono input
(see page 14 for the specication).
DVD
Intended for the analogue outputs from a DVD-player.
AV
Intended for the analogue outputs from general audio-
visual equipment, such as a VCR, digital TV/satellite
receiver, or Nicam tuner.
TUNER
Intended for the analogue outputs from an FM, AM or
DAB radio tuner.
CD
Intended for the analogue outputs from a CD player.
AUX
is is intended for general use, or for connecting an
iPod® via an Arcam rLead or rDock. However, it can
also be used to connect the analogue audio outputs
of any unit with a line-level output (such as a games
console or set-top box).
SAT
For connection to a satellite TV receiver or cable box.
Controlling the A28 from a second room
e A28 will require a remote pick-up device with a 12V external power supply (such as a Xantech Dinky
Link) located in Zone 2, together with a power amplier (such as an Arcam A28 or P38) to complete the
system.
e diagram shows the wiring scheme, which also applies to other IR pick-up devices commonly available.
e A28 can also provide a +12V trigger output to control devices such as the power amplier in Zone 2.
e +12V trigger is active when the unit is ‘On’.
Signal
Tip = Signal
REMOTE IN
Dinky Link, located in Zone 2
Sleeve = 0V
Phono input
e phono inputs provide a pre-amplication stage to
treat the low-voltage output from a moving magnet
cartridge. If you have already an external phono amplier
that you wish to use, connect its output to one of the line-
level inputs, such as the AUX input.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam A28 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam A28 in the language / languages: English as an attachment in your email.

The manual is 0,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Arcam A28

Arcam A28 User Manual - German - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info