578744
10
Zoom out
Zoom in
Previous page
1/17
Next page
E-10
Switching the A28 on
e POWER button switches the unit on and o;
alternatively, the unit can be switched in and out of
stand-by mode by pressing the
2
button on the remote
control handset.
e power light (next to the A28 Integrated Amplier
text) indicates the state of the amplier:
1. A red light means that the amplier is in stand-by
mode;
2. When you switch your amplier on, the power
light glows amber for a few seconds; during this
time the outputs are muted;
3. e light changes to green when the amplier is
ready for use.
e power light may ash if a fault has occurred –
the fault type is shown on the display. See page 15,
‘Troubleshooting’, for help in resolving fault situations.
If the fault cannot be cleared, unplug your amplier and
contact your Arcam dealer.
Changing the volume
Use the control knob to change the volume. Turn the
knob clockwise to increase the volume, anti-clockwise
to reduce it.
e output of the A28 can be silenced by pressing MUTE
on the front panel or remote control. Press MUTE for a
second time (or change the volume) to cancel the mute.
SP1 and SP2
ese buttons allow you to switch the main speakers
(connected to the lower set of speaker terminals) and
secondary speakers (connected to the upper set of
speaker terminals) on and o.
e light above each button glows if the corresponding
speakers are currently selected. If you have connected
the A28 to the speakers using the single-wired
conguration described on page 9, then the SP1 light
should be illuminated; if you have used the bi-wiring
conguration described on page 9, both SP1 and SP2
must be switched on. Note that when both lights are o,
the amplier will appear not to work, as all speakers are
disconnected.
When listening to ‘loud’ inputs, such as CDs, the
amplier may reach its full power before the display
shows 72 (maximum volume), in contrast, lower-level
inputs, such as tuners, will sound quieter for the same
volume level shown. To compensate for this, the input
levels of each source may be adjusted. is can be done
using the A28 setup menu (see page 11).
operation
Selecting an audio source
A source-selection button is used to select the source
that is connected to the input corresponding to the
button.
Listening using headphones
e headphones socket (PHONES) accepts headphones
with an impedance rating between 8 and 2k, tted
with a 6.5mm stereo jack plug.
e pre-amp. outputs and speakers are muted when
headphones are plugged in. e headphones socket is
always active, unless the volume has been muted.
Balance
In addition to the A28 setup menu (see page 11), you
can also set le-right stereo balance directly by pressing
the front-panel BALANCE button and adjusting the
balance with the control knob.
Display
e DISPLAY front panel button changes the display
brightness. ere are three brightness levels: ‘on,
dimmed’ and ‘o. If the A28 is switched o while the
display is set to ‘o, the display is set to ‘dimmed’ when
the A28 is switched on again.
Recording an audio source
e A28 allows listening to and recording from the
same source, or listening to one source whilst recording
another. e signal to be recorded is sent to both the AV
and AUX output sockets.
Selecting the source for recording
e recording outputs can be congured in two ways:
1. To record the source being listened to;
2. To record a particular (specied) source,
regardless of what is being listened to.
To record the source being listened to, press the
RECORD button and turn the control knob if necessary
until the display shows ‘REC SRC. Aer a few seconds,
the display reverts to showing the volume level, and you
are ready to record. In this conguration, selecting a
dierent input changes the source that is routed to the
recording outputs.
To record one source whilst listening to another, press
RECORD and turn the control knob until the display
shows ‘Rec ’ followed by the name of the input (Sat,
Phono, CD, Tuner, AUX or DVD) that you wish to
record from. You are now ready to record.
Press a dierent source button to change the source that
you wish to listen to – this does not alter the source that
is routed to the recording outputs.



  






 
av-ph 20
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam A28 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam A28 in the language / languages: English as an attachment in your email.

The manual is 0,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Arcam A28

Arcam A28 User Manual - German - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info