578744
11
Zoom out
Zoom in
Previous page
1/17
Next page
E-11
English
Adjusting listening settings
e A28 allows you to customise various features of the
amplier to t your system. Use this diagram to help you
navigate through the available conguration options.
In the diagram, the control knob is shown as .
Normally, the display shows the source and the current
volume.
Press MENU once to enter the setup menu, use the
control knob to cycle through the menu items. When
A28 setup
you have found the setting that you wish to adjust (as
shown on the front panel display), press OK. To adjust
the chosen setting, use the control knob. Press MENU to
store the change and return to volume display mode – or
press OK again to move to the next setting.
Note that the menu will time-out aer a short period
without pressing a button or adjusting the control knob,
with the display reverting to the current volume.
e following items can be adjusted from the setup
menu:
Conguring your A28 amplier
Balance
is allows you to adjust the output balance between le and right channels. e balance
control is also available directly by pressing the front panel BALANCE button.
Vol Res ere are three volume-display options to chose from: ‘Std, ‘Fine’ or ‘Ref. Standard and
Fine represent dierent levels of volume-control sensitivity; the Reference setting gives
absolute increments in 0.5dB steps.
I/P Trims
Input trims are used to compensate for variations in output levels of dierent source
equipment. If, for example, your CD player is louder at a given volume display value
than other inputs, you can attenuate it by using this setting so that it matches your other
components.
Use the source-select buttons to select the input you wish to adjust, then the control knob
to set (increase or decrease) the input volume for that source.
Proc Mode
Processor mode enables you to x the gain (volume setting) of your A28. e A28 (in
combination with a power amp.) can then be used to drive the front le and right speakers
of a surround-sound system, when fed from a separate processor. e volume of the entire
system can then be controlled using the processor.
Feed the sound from the processor into the AV input, then set the gain of the A28 to match
the ampliers that drive your other loudspeakers.
REC SRC
To record one source while listening to another, turn the control knob until the display
shows ‘Rec ’ followed by the name of the input (Sat, Phono, CD, Tuner, AUX or DVD)
that you wish to record from. e record source control is also available directly by
pressing the front panel RECORD button.
Max onvol
is can be used to limit the maximum volume the amplier operates at when it is rst
switched on: the A28 comes on at the (reduced) ‘Max. On Volume’ level if the last-used
volume exceeds this value.
If this item is set to ‘Off, the A28 always comes on at the last used volume, even if this is
very loud.
Reset Conrming ‘Yes’ restores all amplier settings to their factory defaults.
VOLUMEOOO
BALANCEOO
VOL RESOO
I/PoTRIMS
PROC MODE
MAX ONVOL
RESET0000
L , ; , R
RES REF
RES FINE
RES STD
AUX TRM -8 . . . 8
PROC AV
FIXED 3 . . . 72
ONVOL OFF
ONVOL 3 . . . 72
NO YES
REC SRC
REC SATPHONOCD
TUNERAUXDVD
‘Power On’ state
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam A28 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam A28 in the language / languages: English as an attachment in your email.

The manual is 0,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Arcam A28

Arcam A28 User Manual - German - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info