541356

Allen-Heath GL 4000 Manual

23
Zoom out
Zoom in
Previous page
1/54
Next page
22
LR
THE CONSOLE LR AND LR2 OUTPUTS - In
addition to the main L and R outputs the GL4000
includes a secondary pair of outputs called L2
and R2. These follow the LR mix and may be
selected either pre or post LR faders. As with
the matrix outputs an OUTPUT REVERSE
switch is included on each to swap the L(R)2
jack output with aux 9(10) XLR and to switch in
the insert. Use this when you need to drive long
cable runs, interface with standard XLR
multicores and cables, or insert EQs, delays or
other signal processors.
Typical applications include:
Additional stereo speaker feeds - For
zoning, dual speaker systems and delay fills.
2-track Recording - For an independent feed
from the LR mix, pre or post fader. Can also be
used as a simple stereo broadcast feed.
L(R)2 MASTER - Selects and controls the L
and R secondary outputs. Adjust LEV to trim
the output level to match the connected
equipment. ON switches the output on or off.
AFL lets you monitor the signal post level trim,
post insert but pre ON switch.
METER - 12 segment, 3 colour peak reading
meter for L and R. Each meter can be switched
to monitor either the main fader signal (normally
L and R) or the small fader signal (normally aux
9 and 10). The switch does not affect the
optional VU meterpod which always follows the
main fader signals. The L and R meters can be
switched using STEREO PFL METER to be
interrupted by stereo PFL when selected.
L(R) MASTER - The LR mix is normally
controlled using the 100mm faders. If L(R)
REV is pressed the main faders follow the aux
9(10) signals and L(R) is available on the small
faders. As with the groups: automated MUTE,
pre fade mix meters, matrix sends and AFL are
available.
L(R) TO MONO - The required amount of post
fade L and R signal may be added to the M mix
using these controls. You can create a quick
mono output by mixing in equal amounts of L
and R signal. You can also use L and R as
additional subgroups to M.
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Allen-Heath GL 4000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Allen-Heath GL 4000 in the language / languages: English as an attachment in your email.

The manual is 2,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info