603978

Al-ko BC 225 L Manual

21
Zoom out
Zoom in
Previous page
1/264
Next page
Translation of the original operating instructions
22
Choke settings:
CHOKE RUN
Note the following for a cold start of the
BC 225 L and BC 225 B:
1. Placethestrimmeratonthegroundawayfrom
any other objects.
2. Ensure that the cutting tool is not in contact with any
objects or the ground.
3. Ensure that it is stable.
4. Hold the device with your left hand. With your right
hand, grip the starter cord.
5. Do not stand or kneel on the support.
Always pull the starter cord straight out. Never allow it
to snap back abruptly.
Starting the BC 225 L
BC 225 L cold start (Fig. 5) (Fig. 6)
5-1 „Start“ - „Stop“ ignition
5-2 Throttle lock
5-3 Gas lever
6-1 Airltershroud
6-2 Petrol tank
6-3 „Choke“-„Run“ignitionap
6-4 Primer (cold-start diaphragm pump)
6-5 Starter cord
1. Set the ignition switch to the “Start” position.
2. Press and hold the throttle lock, press the throttle.
3. Set the choke to the “CHOKE” position.
4. Press the cold start membrane pump 10 times.
5. Pull out the starter cord 3 or 4 times until the engine
starts up (ignites) audibly for a brief time.
Pull the cord briskly with uniform force.
6. Once the engine has started: set the choke to “RUN”.
7. Pull out the starter cord until the engine starts.
8. If the engine does not start, repeat steps 1 to 7.
BC 225 L warm start (Fig. 5) (Fig. 6)
1. Set the ignition switch to the “Start” position.
2. Set the choke to „RUN“. Pull the starter cord - the en-
gine will start.
Engine does not start:
Set the choke to the “RUN” position.
Pull the starter cord 5 times.
If the engine still does not start:
Wait 5 minutes and then try again with the gas
lever pressed down.
Refer to the “Troubleshooting” chapter.
Switch off the engine (Fig. 5)
1. Release the gas lever and let the engine idle.
2. Set the ignition switch to “STOP”.
Caution!
The engine and cutting parts will continue to run-on after
switching off - risk of injury!
Starting the BC 225 B
BC 225 B cold start (Fig. 8) (Fig. 9)
8-1 „Start“ - „Stop“ ignition
8-2 „Lock-Off“ switch
8-3 Throttle lock
8-4 Gas lever
9-1 Airltershroud
9-2 Petrol tank
9-3 „Choke“-„Run“ignitionap
9-4 Primer (cold-start diaphragm pump)
9-5 Starter cord
1. Set the ignition switch to the “Start” position.
2. Lock the gas lever:
Press and hold the throttle lock
Press and hold the throttle
Press and hold the „Lock off“ switch
Release the throttle
The throttle runs at full throttle.
Release the „Lock off“ switch.
3. Set the choke to the “CHOKE” position.
4. Press the cold start membrane pump 10 times.
5. Pull out the starter cord 2 or 3 times until the engine
starts (ignites) audibly for a brief time.
Pull the cord briskly with uniform force.
6. Once the engine has started: set the choke to “RUN”.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Al-ko BC 225 L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Al-ko BC 225 L in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 9,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info