630535

Akai EWI 5000 Manual

34
Zoom out
Zoom in
Previous page
1/49
Next page
34
Using Effects (FX)
You can use the EWI5000's FX Menu to apply and edit three different effects to its audio
output: Reverb, Chorus, and Delay.
Important: Your EWI5000's audio output must be enabled to edit its effects. If you are using it
as a MIDI controller only (its Preset LED or User LED is flashing), enable its audio output by
pressing and holding the Power Button until its Preset LED or User LED is lit solid.
To enter the FX Menu, press and hold the FX Button, and then use the Hold Button and
Interval Button to select rb (Reverb), ch (Chorus), or dL (Delay). Release the FX Button to
edit that effect's parameters, described below in each section.
To exit the FX Menu, press the FX Button once.
Learn more about setting the parameters for the Reverb, Chorus, and Delay effects in this
chapter.
Reverb
Reverb is a spatial effect, simulating the nuanced reverberation of sound in the space of a
particular room.
To edit the Reverb effect:
1. Press and hold the FX Button, and then use the Hold Button and Interval Button to
select rb (Reverb).
2. Release the FX Button. The effect level will appear in the display.
3. To set the effect level, use the Hold Button and Interval Button (00–99).
Tip: You can also set the effect level by using EWI5000's Reverb Parameter Knob.
To select another parameter to edit, or press and hold the Trans Button or Level Button,
use the Hold Button and Interval Button to select the parameter, and then release the
Trans Button or Level Button:
• ut (Wet/Dry): This determines the blend between the "wet" (affected) and "dry"
(unaffected) signal. 00 is all dry, and 99 is all wet, while 50 is approximately an equal
mix of both.
• dP (Damping): This determines how much higher frequencies are absorbed by the
simulated room as the reverbating sound decays over the time. At 00, no high
frequencies are absorbed, allowing for their maximum decay time. A setting of 99
results in the most absorption of higher frequencies, creating a warmer sound.
• ud (Width): This determines the width of the stereo image generated by the reverb.
00 produces the narrowest stereo image, while 99 produces the widest.
• rS (Room Size): This determines the size of the room that the reverb will simulate.
00 corresponds to a small room size, while 99 corresponds to a large one.
4. Press the FX Button once to exit the FX Menu.
… 34 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Akai EWI 5000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Akai EWI 5000 in the language / languages: English as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info