618070
14
Zoom out
Zoom in
Previous page
1/52
Next page
14
A300 AI OPERATING MANUAL
© 2002 Design, 2011 Doc. No. 12-7265-r01 (12/28/11)
HISTORY MODE
History is a summary of data recorded during all NORM and GAUG dives conducted.
History 1, information includes (Fig. 18):
> Graphic TOTAL, or NO DIVES YET (if new unit).
> Total dives recorded (up to 9999) with graphic DIVES
.
> Total dive hours recorded (up to 9999) with graphic HOURS.
> Graphic HIST.
S (< 2 sec) to access History 2.
S (2 sec) to revert to Main Menu.
History 2, information includes (Fig. 19):
> Graphic SEA (or EL2 to EL7), highest Altitude at which a dive was conducted.
> Max Depth recorded with FT (or M) and MAX icons.
> Longest dive time (minutes) recorded during a single dive (up to 599 min) with graphic EDT.
> Lowest Temperature recorded during a dive with icon and graphic F (or C).
• S (< 2 sec) to revert to Main Menu.
S (2 sec) to revert to History 1.
ID - SN
This information should be recorded and kept, it will be required in the event that your unit requires factory service.
ID (Identification), information includes (Fig. 20):
> Graphic ID.
> Graphic SN with the factory programmed serial number.
> Graphic FIRMWARE with 1A (or higher)*, indicating the Firmware revision level currently installed in the unit.
> Graphic LCD with 01 (or higher), indicating the Display's revision number.
*This number will change if Firmware is updated by factory service or by future download of revised firmware from the AERIS web site
.
• S (< 2 sec) to revert to Main Menu.
NORM DIVE PREVIEW
This feature provides quick access to a screen that displays up to 4 settings that can be pre selected* using the Set P Menu.
Preview, information includes (Fig. 21):
> Graphics Nor and PREV.
> Selections* with Set Points entered using that menu.
*If no selections have been made yet, the graphics USE SET P TO SELECT ENTRIES will be displayed.
S (< 2 sec) to revert to Main Menu.
SET GROUPS
Information that follows describes the selections contained in the NORM Set Groups (F, A, U, T, S, D, P) that are accessed from
the Set Menu (page 13).
Main Menu >> Set Menu >> Set Group Menu >> Set Selection.
SET F (FO2)
Each Gas has an individual FO2 setting with an associated PO2 Alarm setting.
Default settings are FO2 Air with no PO2 value for Gas 1, and Off for Gas 2, 3, 4. Settings revert to the defaults when 24 hours
elapse without conducting a dive.
When FO2 is set for Air -
> calculations are the same as when FO2 is set for 21%.
> it remains set for Air until set for Nitrox (21 to 100%).
> O2 data (such as PO2, O2%) will not be displayed at any time during the dive, on the surface, or in Plan mode.
> MODs (Max Operating Depths) will not be displayed on the FO2 set screen.
> internally, it will keep track of O2 data for use if FO2 is subsequently set for Nitrox for repetitive dives.
When FO2 is set for Nitrox -
> The Air option will not be displayed as an FO2 setting until 24 hours elapse after the last dive.
When FO2 is set for OFF (Gas 2, 3, 4) -
> That Gas will not be available in the Gas Switch routine during dives (no Switch To - screen).
Fig. 18 - HISTORY 1
Fig. 19 - HISTORY 2
Fig. 20 - A300 AI ID









Press S (< 2 sec) to access.
Fig. 21 - PREVIEW
(selected settings)
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aeris A300 AI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aeris A300 AI in the language / languages: English as an attachment in your email.

The manual is 11,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info