648332
21
Zoom out
Zoom in
Previous page
1/76
Next page
21
Installation – for qualied contractors
Note
» Mount the appliance on the wall. The wall must
have a sufcient load-bearing capacity.
9.2 Water installation
A safety valve is not required.
» Flush the water line thoroughly.
» Ensure that the ow rate for switching on the appli-
ance is achieved (see chapter "Installation / Spec-
ication / Data table", On). If the ow rate is not
achieved, remove the ow limiter (see chapter "In-
stallation / Installation, Removing the ow limiter").
» If the required ow rate is not achieved when the
draw-off valve is fully opened, increase the water line
pressure.
Taps
Use appropriate pressure taps. Open taps are not per-
mitted.
Note
Never use the shut-off valve in the cold water inlet to
reduce the ow rate. The shut-off valve is intended
to shut off the appliance.
Permissible water line materials
Cold water inlet line:
Galvanised steel pipe, stainless steel pipe, copper
pipe or plastic pipe
DHW outlet line:
Stainless steel pipe, copper pipe or plastic pipe
!
Material losses
If plastic pipework is used, take into account the
maximum inlet temperature and the maximum per-
missible pressure (see chapter "Installation / Spec-
ication / Data table").
Flexible water connection lines
» If the appliance is installed with exible water con-
nection lines, ensure that the bayonet ttings of
the pipe bends do not become twisted inside the
appliance.
» Secure the back panel at the bottom with two addi-
tional screws.
10. Installation
10.1 Standard installation
Electrical connection from above; installation on un-
nished walls
Water connection on unnished walls
DDLE Basis 18/21/24: Connected load 21 kW preset
For further installation options, see chapter "Installation /
Installation / Installation options":
Electrical connection from below on unnished walls
Electrical connection on nished walls
Connecting a load shedding relay
Undersink installation, water connections from above
Water installation on nished walls
Operation with preheated water
Temperature limit
Opening the appliance
D0000041615
» Open the appliance by releasing the snap lock.
NT
T-
so
X1
26_02_02_0762
» Remove the back panel by pressing the two locking
hooks and pulling the lower section of the back panel
forwards.
Preparing the power cable
160
≥ 30
26_02_02_0887
Fitting the wall mounting bracket
26_02_02_0972
» Mark out the holes for drilling with the installation
template. If the appliance is to be installed with water
connections on nished walls, also mark out the x-
ing holes in the lower part of the template.
» Drill the holes and secure the wall mounting bracket
with 2 screws and 2 rawl plugs (screws and rawl
plugs are part of the standard delivery).
» Fit the threaded stud provided.
» Mount the wall mounting bracket.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG DDLE Basis 13 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG DDLE Basis 13 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 19,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info