755222
10
Zoom out
Zoom in
Previous page
1/16
Next page
Operating Instructions – Terxon L
10
7.3. Silencing an alarm
If an alarm has occurred and you want to silence the sounders, do the following:
1. Enter your user code on the keypad or hold your chip key against the
control panel. This stops the alarm tone from the internal and external
alarm sounders.
Even if your user code does not give you access to the partition, the internal
and external alarm tones are stopped. However, the exits and the strobe are
not reset!
2. The display temporarily shows details of the alarm including the affected
zone, the date and the time.
3. An alarm message appears and tells you that the system must to be reset.
7.4. Resetting the system
By resetting the system, you can get an overview of the alarm messages in the
event memory. If you reset the system, the alarm messages of the display are
deleted. In some cases, you may not be able to set your alarm system until you
have reset it.
Important ....................................................................................................................
Every user can silence the sounders and view the alarm messages. However,
some alarms need an engineer code to reset the system.
If the system has to be reset, the keypad sounder may emit a warning chime
every minute.
To reset your alarm system:
1. Enter your user code on the keypad or hold your chip key against the
control panel when you see alarm messages on the display.
2. The display shows how many alarm messages there are (see figure on the
left).
3. Press to view the messages one after the other.
Important ....................................................................................................................
You can press to set/unset the system without deleting the alarm messages.
4. After reading each alarm message, the message shown on the left is
displayed and you can reset the system. Confirm reset with .
The alarm messages should not continue to be displayed unless:
- The reason for the alarm still exists.
- You need an engineer to reset the system.
7.5. Further options
7.5.1. Special user codes
Depending on the configuration of your alarm system, special user codes can run
the following features:
! Alerts !
01:53 Sat 01 Jan
! Alerts !
17:38 Wed 16 MAR
0001 Faults
[ENT] To Scroll
ALARM 0003
08:13:45 01/01
Press ENT
To Reset
Alarm 002
01:53 Sat 01 Jan
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Abus Terxon LX - AZ4200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Abus Terxon LX - AZ4200 in the language / languages: English as an attachment in your email.

The manual is 0,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Abus Terxon LX - AZ4200

Abus Terxon LX - AZ4200 Installation Guide - English - 116 pages

Abus Terxon LX - AZ4200 Installation Guide - German - 31 pages

Abus Terxon LX - AZ4200 User Manual - German - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info