534678

3Dprintingsystems UP Plus Manual

46
Zoom out
Zoom in
Previous page
1/56
Next page
UP Plus
3D Printer User Manual
bearing and slide the
platform
6.7 Spare parts
Almost all the plastic parts on the printer are printed by the U
spare parts for your printer, the files for all spare parts can be found in the C:
(x86)\UP\Example\
Spare Part
6.8 Leveling the platform
There are two methods to level the platform, choose a
6.8.a
Software Platform Leveling Calibration
Ensure your Perfboard is clean and smooth both sides, as a
small piece of plastic could cause the leveling to be uneven.
Intilise the printer.
Click “3D Print” \
“ Platform Ca
Click and long press the
green
a high height like 135mm.
Move the nozzle /
platform to each of the 9 locations on the
platform by clicking
the corresponding location number (1,
2...9). Find out which
one of the 9 locations that
smallest
gap between the nozzle and platform. That location
is the highest point on the platform. Move the nozzle to the
highest point on the platform and make sure the gap between
the nozzle and the highest point is zero.
Click button “Set nozzle height”
Move
the nozzle and platform to each of the other 8 locations
and measure the gap between one by one. Beside each of the
9 locations is a box with the numbers inside, select one of the
10 numbers (0.1, 0.2...1) can lift the platform to a corr
sponding height. U
se that number when it makes the gap
between the nozzle and platform is zero.
After all of the 9 location are me
“Apply current vslue”
at the bottom to apply the final nozzle
height. A dialogue will pop up when the calibration is
cessful.
Close the platform calibration dialogue and
with this file
http://3dprintingsystems.com/boarder
4.
Troubleshooting
3D Printer User Manual
v 2013.6.10
platform
in the appropriate direction to spread the grease.
Almost all the plastic parts on the printer are printed by the U
P
printer itself. If you need to print
spare parts for your printer, the files for all spare parts can be found in the C:
Spare Part
s folder.
6.8 Leveling the platform
method that works best for you.
Software Platform Leveling Calibration
Ensure your Perfboard is clean and smooth both sides, as a
small piece of plastic could cause the leveling to be uneven.
“ Platform Ca
librate”
Note: T
he allowed largest calibration
distance between nozzle and platform is
1mm.
Make sure all nine points are
within this limitation.
Make sure the gap between nozzle and
the highest point on the platform is
zero.
green
up arrow to lift the platform to
platform to each of the 9 locations on the
the corresponding location number (1,
one of the 9 locations that
has the
gap between the nozzle and platform. That location
is the highest point on the platform. Move the nozzle to the
highest point on the platform and make sure the gap between
the nozzle and the highest point is zero.
Click button “Set nozzle height”
the nozzle and platform to each of the other 8 locations
and measure the gap between one by one. Beside each of the
9 locations is a box with the numbers inside, select one of the
10 numbers (0.1, 0.2...1) can lift the platform to a corr
e-
se that number when it makes the gap
between the nozzle and platform is zero.
After all of the 9 location are me
asured and set, click the
at the bottom to apply the final nozzle
height. A dialogue will pop up when the calibration is
suc-
Close the platform calibration dialogue and
do a test print
http://3dprintingsystems.com/boarder
-print.UP3
Troubleshooting
printer itself. If you need to print
spare parts for your printer, the files for all spare parts can be found in the C:
\Program Files
method that works best for you.
he allowed largest calibration
distance between nozzle and platform is
Make sure all nine points are
within this limitation.
Make sure the gap between nozzle and
the highest point on the platform is
… 46 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for 3Dprintingsystems UP Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of 3Dprintingsystems UP Plus in the language / languages: English as an attachment in your email.

The manual is 7,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info