534678

3Dprintingsystems UP Plus Manual

45
Zoom out
Zoom in
Previous page
1/56
Next page
UP Plus
3D Printer User Manual
6.3 Cleaning the
outside of the
After a lot of printing, the nozzle may be covered with a layer of oxidized
of the nozzle
. When the printer is printing, this oxidized ABS may melt on th
ate discolored spots in the
model. To avoid this you need to regularly clean the nozzle.
Firstly,
move the platform to the bottom, then do a
oxidized ABS.
Lastly, use some heat-
resistant material, like 100
percent cotton cloth or soft paper. A pair of
twee
zers will also be required. Then clip paper or
some other heat-
resistant things with tweezers to
clean up the nozzle.
6.4
Removing / Changing the nozzle
Should the nozzle become blocked, you may need to remove it in order to unblock, or change it. To
remove the nozzle,
first click Withdraw in the maintenance screen, then once the printer is at 260c,
use the nozzle wrench provided in the toolkit that comes
ONLY
remove the nozzle when it is hot
er block.
6.5 Cleaning the
Perfboard
To clean the platform use the included Perfboard pokers, or alternatively use the spatula and
simply just scrape off the surface plastic until
for longer the plastic left in the Perfboard becomes soft and the extruded plastic sticks to it, thus
not requiring the holes of the Perfboard to be empty/clean.
6.6
Lubrication of bearings
The bearings on the UP 3D
Printer may occasionally require a bit of lubrication to keep it opera
ing smoothly. The recommended grease to use is lithium grease. When lubricating the bearings,
first clean off as much old grease as possible from the bearings, and then apply
If the nozzle is blocked, remove the nozzle and clean it.
The extruder and platform are hot. Use gloves when working in this area of
printer.
4.
Troubleshooting
3D Printer User Manual
v 2013.6.10
outside of the
nozzle
After a lot of printing, the nozzle may be covered with a layer of oxidized
black
ABS
. When the printer is printing, this oxidized ABS may melt on th
e nozzle, and may cr
model. To avoid this you need to regularly clean the nozzle.
move the platform to the bottom, then do a
“Withdraw” in order to
heat the nozzle to melt the
resistant material, like 100
percent cotton cloth or soft paper. A pair of
zers will also be required. Then clip paper or
resistant things with tweezers to
Removing / Changing the nozzle
Should the nozzle become blocked, you may need to remove it in order to unblock, or change it. To
first click Withdraw in the maintenance screen, then once the printer is at 260c,
use the nozzle wrench provided in the toolkit that comes
with your UP Printer.
remove the nozzle when it is hot
, trying to remove it while cold will damage the extru
Perfboard
To clean the platform use the included Perfboard pokers, or alternatively use the spatula and
simply just scrape off the surface plastic until
smooth on both sides. If you preheat the
for longer the plastic left in the Perfboard becomes soft and the extruded plastic sticks to it, thus
not requiring the holes of the Perfboard to be empty/clean.
Lubrication of bearings
Printer may occasionally require a bit of lubrication to keep it opera
ing smoothly. The recommended grease to use is lithium grease. When lubricating the bearings,
first clean off as much old grease as possible from the bearings, and then apply
If the nozzle is blocked, remove the nozzle and clean it.
The extruder and platform are hot. Use gloves when working in this area of
printer.
Troubleshooting
ABS
on the outside
e nozzle, and may cr
e-
model. To avoid this you need to regularly clean the nozzle.
heat the nozzle to melt the
Should the nozzle become blocked, you may need to remove it in order to unblock, or change it. To
first click Withdraw in the maintenance screen, then once the printer is at 260c,
, trying to remove it while cold will damage the extru
d-
To clean the platform use the included Perfboard pokers, or alternatively use the spatula and
smooth on both sides. If you preheat the
platform
for longer the plastic left in the Perfboard becomes soft and the extruded plastic sticks to it, thus
Printer may occasionally require a bit of lubrication to keep it opera
t-
ing smoothly. The recommended grease to use is lithium grease. When lubricating the bearings,
first clean off as much old grease as possible from the bearings, and then apply
new grease to the
The extruder and platform are hot. Use gloves when working in this area of
… 45 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for 3Dprintingsystems UP Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of 3Dprintingsystems UP Plus in the language / languages: English as an attachment in your email.

The manual is 7,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info