534678

3Dprintingsystems UP Plus Manual

43
Zoom out
Zoom in
Previous page
1/56
Next page
UP Plus
3D Printer User Manual
6. M
aintenance
6.1
Changing the Material
To change colours or different materials it’s best to f
head.
There are two ways to do this.
1.) During Printing
a. “3D print
>Maint
old filament and cut the end of the new filament and insert into the extruder head,
then click “Extrude”. Once you see the new filament being extruded click “R
sume” If you find the new filament gets j
the end again and “Extrude”. Note: While paused the extruder and the platform
remains heating. Do not leave unattended.
2.) While idle, click
“3D print >Maintenance” then click
ment. (this t
akes a couple of minutes for the extruder to reach 260c)
beeps, you should be able to remove the filament. Then click “Extrude” and load the new
filament –
cut the end off the new filament before loading.
Always use the
Tube or Straw to feed filament in between the roll guide and extruder head.
Push the filament into the hole at the top of the extruder head, with a little pressure, and the e
truder will automatically extrude material.
should be thin, straight
and smooth.
ter the material weight of the spool so the printer can keep track of material usage.
If the nozzle is blocked, remove the nozzle and clean it.
The extruder and platform are hot. Use gloves when working in this area of
printer.
6.2
Vertical Calibration
This is only recommended to carry out if you find that your models are not vertical.
PORTANT: En
sure your platform is level,
calibration values
before starting this process
The Vertical calibration procedure allows you to ensure that the printer platform is perfectly hor
zontal and that the printer prints consistently in the X, Y and Z
4.
Troubleshooting
3D Printer User Manual
v 2013.6.10
aintenance
Changing the Material
/ colours
To change colours or different materials it’s best to f
irst withdraw the material
There are two ways to do this.
>Maint
enance”
then click “Pause”, then click “Withdraw”, remove the
old filament and cut the end of the new filament and insert into the extruder head,
then click “Extrude”. Once you see the new filament being extruded click “R
sume” If you find the new filament gets j
ammed, do another withdraw and cut
the end again and “Extrude”. Note: While paused the extruder and the platform
remains heating. Do not leave unattended.
“3D print >Maintenance” then click
“Withdraw” to remove the old fil
akes a couple of minutes for the extruder to reach 260c)
beeps, you should be able to remove the filament. Then click “Extrude” and load the new
cut the end off the new filament before loading.
Tube or Straw to feed filament in between the roll guide and extruder head.
Push the filament into the hole at the top of the extruder head, with a little pressure, and the e
truder will automatically extrude material.
The plastic thread is squeezed out
of the nozzle
and smooth.
Then in the maintenance window click “New Spool” and e
ter the material weight of the spool so the printer can keep track of material usage.
If the nozzle is blocked, remove the nozzle and clean it.
The extruder and platform are hot. Use gloves when working in this area of
printer.
Vertical Calibration
This is only recommended to carry out if you find that your models are not vertical.
sure your platform is level,
at the correct height
and you have RESET the
before starting this process
!!!
The Vertical calibration procedure allows you to ensure that the printer platform is perfectly hor
zontal and that the printer prints consistently in the X, Y and Z
direction.
Troubleshooting
from the extruder
then click “Pause”, then click “Withdraw”, remove the
old filament and cut the end of the new filament and insert into the extruder head,
then click “Extrude”. Once you see the new filament being extruded click “R
e-
ammed, do another withdraw and cut
the end again and “Extrude”. Note: While paused the extruder and the platform
“Withdraw” to remove the old fil
a-
Once the printer
beeps, you should be able to remove the filament. Then click “Extrude” and load the new
Tube or Straw to feed filament in between the roll guide and extruder head.
Push the filament into the hole at the top of the extruder head, with a little pressure, and the e
x-
of the nozzle
Then in the maintenance window click “New Spool” and e
n-
ter the material weight of the spool so the printer can keep track of material usage.
The extruder and platform are hot. Use gloves when working in this area of
This is only recommended to carry out if you find that your models are not vertical.
IM-
and you have RESET the
The Vertical calibration procedure allows you to ensure that the printer platform is perfectly hor
i-
… 43 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for 3Dprintingsystems UP Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of 3Dprintingsystems UP Plus in the language / languages: English as an attachment in your email.

The manual is 7,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info