534678

3Dprintingsystems UP Plus Manual

44
Zoom out
Zoom in
Previous page
1/56
Next page
UP Plus
3D Printer User Manual
1.
In the UP software, click “3D Print”
menu and click “
Calibrate
2. Click “Reset”
and click
tus bar should then show 0 values as
per picture)
3.
In the UP software open the
files\UP\Example\
Ca
4. Open the “Calibrat
e” box form the “3D Print”
5. 3D Print the
calibration
6.
After the calibration model is printed, measure the X1 and X2 length
pictures below.
Then
enter the measured X1 and X2 values into the appr
Remove the Front
Centre ‘L’ shaped component
into the Z box. If it deviates to the right side, the value
value.
If the deviates to the left, the value
Finally, measure the height of Front
measures near 40mm, enter 40mm as the value.
Click “OK” to record all these v
4.
Troubleshooting
3D Printer User Manual
v 2013.6.10
In the UP software, click “3D Print”
Calibrate
”
and click
OK. (the sta-
tus bar should then show 0 values as
In the UP software open the
Calibration model
located in “
Ca
librate96.UP3”
e” box form the “3D Print”
calibration
model.
After the calibration model is printed, measure the X1 and X2 length
, as shown in the
enter the measured X1 and X2 values into the appr
opriate boxes.
Centre ‘L’ shaped component
, and measure its deviation. Put the exact value
into the Z box. If it deviates to the right side, the value
to
be put into the Z box will be a positive
If the deviates to the left, the value
to
put into the Z box will be a negative value.
Finally, measure the height of Front
Center component, which should
be 40mm.
measures near 40mm, enter 40mm as the value.
Click “OK” to record all these v
alues and exit the calibration window.
Troubleshooting
located in “
C:\program
, as shown in the
, and measure its deviation. Put the exact value
be put into the Z box will be a positive
put into the Z box will be a negative value.
be 40mm.
If the part
… 44 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for 3Dprintingsystems UP Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of 3Dprintingsystems UP Plus in the language / languages: English as an attachment in your email.

The manual is 7,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info