534678

3Dprintingsystems UP Plus Manual

48
Zoom out
Zoom in
Previous page
1/56
Next page
UP Plus
3D Printer User Manual
9.
The platform rests on a tripod (three
spru
ng screws) and in order to level it
tighten or loosen
each of the three screws
until the distance between the nozzle a
the platform is equal
at each corner.
10.
As the platform gets more level, increase
the platform
height to the nozzle, so it is
easier see the gap.
You will most likely need to repeat the process 5
a few times
going in a clockwise manner. Each
time r
educing the amount of turn on the screws.
Loosen a screw and the related corner of platform will rise. Tighten, or loosen, the screws until
you have the same gap between the nozzle and the platform at all four corners of platform.
7.0.
Tips & Tricks
parts
When printing with ABS Plastic
the nozzle at 260c
it comes out in an expanded state
If the part cools unevenly then it will warp or lift. This normally happens in the corners of the part
as the corners are exposed to air circulating around the printer. The larger the parts surface area on
the platform, normally the worse the problem.
Some Tips to reduce warping:
• Make sure the
platform
up to near the nozzle and in maintenance, move the head to each corner to ensure the di
tance between nozzle and
• Make sure the
platform
platform
heated after printing)
•
Keep the printer away from any breezes
• Print hollow -
The less mass of plastic the less heat in the centre, the less warping.
•
Print the object with the least surface area on the platform,
more successful printing and saves material in the long run.
• P
rint closer to the Perfboard
• Keep the
Perfboard
4.
Troubleshooting
3D Printer User Manual
v 2013.6.10
The platform rests on a tripod (three
ng screws) and in order to level it
, you
each of the three screws
until the distance between the nozzle a
nd
at each corner.
As the platform gets more level, increase
height to the nozzle, so it is
You will most likely need to repeat the process 5
-9
going in a clockwise manner. Each
educing the amount of turn on the screws.
Loosen a screw and the related corner of platform will rise. Tighten, or loosen, the screws until
you have the same gap between the nozzle and the platform at all four corners of platform.
Tips & Tricks
to avoid warping / lifting
When printing with ABS Plastic
it is important to understand the material. ABS
is extruded from
it comes out in an expanded state
, like most materials as it cools it will shrink.
If the part cools unevenly then it will warp or lift. This normally happens in the corners of the part
as the corners are exposed to air circulating around the printer. The larger the parts surface area on
the platform, normally the worse the problem.
Some Tips to reduce warping:
platform
is level! -
Remove the Perfboard and clips, bring the
up to near the nozzle and in maintenance, move the head to each corner to ensure the di
tance between nozzle and
platform is the same at each corner.
Check and recheck!!!
platform
is nice and toasty!
(do a previous print or two and keep the
heated after printing)
– Keep the extruder
door closed during printing
Keep the printer away from any breezes
, air con, this cools
the model to
The less mass of plastic the less heat in the centre, the less warping.
Print the object with the least surface area on the platform,
creates more support
more successful printing and saves material in the long run.
rint closer to the Perfboard
– Move the nozzle closer to the platform.
Perfboard
smooth -
Clean the perfboard, by scrapping off the surface and e
Troubleshooting
Loosen a screw and the related corner of platform will rise. Tighten, or loosen, the screws until
you have the same gap between the nozzle and the platform at all four corners of platform.
to avoid warping / lifting
is extruded from
, like most materials as it cools it will shrink.
If the part cools unevenly then it will warp or lift. This normally happens in the corners of the part
as the corners are exposed to air circulating around the printer. The larger the parts surface area on
Remove the Perfboard and clips, bring the
platform
up to near the nozzle and in maintenance, move the head to each corner to ensure the di
s-
Check and recheck!!!
(do a previous print or two and keep the
door closed during printing
.
the model to
fast.
The less mass of plastic the less heat in the centre, the less warping.
creates more support
but
Clean the perfboard, by scrapping off the surface and e
n-
… 48 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for 3Dprintingsystems UP Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of 3Dprintingsystems UP Plus in the language / languages: English as an attachment in your email.

The manual is 7,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info