666219
39
Zoom out
Zoom in
Previous page
1/63
Next page
Pedel
1
Assignment
This function allows you to determine which func-
tion will be controlled by the footswitch or pedal
connected to the PEDALISW
1
terminal on the rear
panel.
SYS System Setup
(
bPEDAL1
BYPASS
I
Four settings are provided:
BYPASS: This has the same function as that of
BYPASS key on the front panel.
Each press of
the footswitch
turns
on or off the bypass function,
which cancels all effects and outputs only the
unprocessed signal.
.
PATCH
UP:
Each press of the footswitch selects
Patch programs, in their ascending numerical
order,
PATCH
DOWN:
Each press of the footswitch
selects Patch programs, in their descending
numerical order.
MODULATION: (For pedal only) Operation of a
pedal continuously changes effect parameters in
real time. Refer to the section, REAL-TIME
EFFECT MODULATION.
The correct polarity of the footswitch is automati-
cally sensed and set when the power is turned on.
Note: The Bypass, Patch Up and Patch Down
settings are designed for use with an
on/off foot-
switch. The Modulation setting is for use with a
volume pedal type foot controller.
Pedal
2
Assignment
This
function allows you to determine which func-
tion will be controlled by the footswitch or pedal
connected to the PEDAL/SW
2
terminal on the
rear panel.
SYS System Setup
(
b
PEDAL2
BYPASS
The settings and operation
same as that of the Pedal
1
above.
Input
Peak
Sensitivity
for Pedal
2
are the
Assignment function
This function determines the input signal level at
which the peak indicator will light.
SYS System Setup
I
Weak=+OdB
Three input sensitivity settings are provided:
+
0
dB
+
6
dB
+
12 dB
Note: This function does not actually change the
input sensitivity or the amount of headroom. It is
meant as a convenience for those who customarily
use "hot" signals that would ordinarily trigger the
peak warning.
GROUP
CHANGE
MODE
OVERVIEW
In the Group Change mode you can the Routing
(Group) of the 9010. Each Routing uses a different
signal routing configuration and employs different
effect modules. For more information on Routings,
refer to ROUTINGS, p.14, in the section THE 9010
SYSTEM.
Entering
the
Group
Change
Mode
To enter this mode, press the MODE key as many
times as necessary to call up the
"GRP"
(Group
Change mode) display:
GRP Group Change
I
Group
,I
<RTG
1>
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zoom 9010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zoom 9010 in the language / languages: English as an attachment in your email.

The manual is 2,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info