666219
38
Zoom out
Zoom in
Previous page
1/63
Next page
program change number 00 and 03.
When Group
2
is selected,
6
and 7 are selected by
program change number 05 and
06.
When Group
3
is selected,
2
and 3 are selected by
program change number 01 and 02.
When Group
4
is selected,
5
and
8
are selected by
program change number
04
and 07.
In this example, the Patches will not be changed by
any other numbers.
Having Patch programs of a Group scattered over the
memory locations like in the example above makes
selection particularly difficult. However, by setting
specific
MlDl program change numbers to select
specific Patch numbers in this menu, you can assign
them in any convenient order.
Note:
For the technically minded, the correspon-
dence between the bank number and the 14-bit bank
select MlDl messages is shown below:
1
I
MSB
I
LSB
I
1
User memory
1
00 H
,
00 H
1
CARD
1 memory
OOH
OIH
I
CARD
2
memory 00
H
02
H
1
1(1
03
ti
CARD
3
memow
Preset memory
7
FH
7
FH
1
SYSTEM
MODE
OVERVIEW
In the System mode you can:
Set the conditions for the beep sound.
Assign the functions performed by the connected
footswitches or pedals.
Set the input peak sensitivity.
Entering the System Mode
To enter this mode, press the
MODE
key as many
times as necessary to call up the
"SYS"
(System
mode) display:
SYS System Setup
I
,BEEP
All
On
To exit this mode, select a different mode by pressing
the MODE key again, or press the EXIT key.
THE
FUNCTIONS
The functions below are given in the order they
appear on the display. Select the function with the
EDlT DIAL, press the DlAL key (turning LED to red),
then turn the EDlT DlAL again to change the parame-
ter.
Beep Sound
The 9010 normally plays a warning "beep" from
a
small internal speaker when a key has been
pressed or when an operation error occurs. This
function allows you to determine the conditions
under which the beep will sound. The beep
sound can also be turned off here.
SYS System Setup
I
,BEEP
All
On
All On: Sounds when front panel keys are
pressed and when operation errors occur.
All Off: Cancels the beep sound.
Key
On:
Sounds only when front panel keys are
pressed.
Sys On:
Sounds only to indicate operation errors.
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zoom 9010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zoom 9010 in the language / languages: English as an attachment in your email.

The manual is 2,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info