Manual Zipper ZI-RPE60 (page 24 of 52) (English, German, French, Spanish)

644523

Zoom out

Zoom in

1/52

2.5.4 Controlling the belt

NEVER try to control the belt at running

engine. This leads to serious injuries on

your hand.

Remove the safety cover. It is fixed on

the ZI-RPE60 with two six-head screws

and on the ZI-RPE90 with four six-head

screw.

The belt tension is right when you can

push it in the middle 10-15 mm in.

After controlling you must mount the

safety cover again.

A loose belt reduces the power. This

leads to a less powerful tamping and it

can also cause early deterioration of the

belt.

When the belt is battered you must

change it immediately.

2.5.5 Changing the belt

Remove the safety cover.

Loosen the belt by loosening the screw

with which the engine block is fixed on

the plate. Now you can slide the engine

block in the grooves and so you can

loosen the belt.

Let a wrench latch into the screw of the

belt (below). Turn the wrench anti-

clockwise so that the belt becomes unfas-

tened.

Let the belt latch in the lower vibration

belt and move it to the left side of the

upper clutch. Turn the wrench so that the

belt gets placed back.

2.5.6 Tensioning the belt

Tension the belt by sliding the engine

block on the plate. For this you can use a

six-head adjusting screw which is front-

wards on the side of the engine block.

The tension is correct when the distance

between your fingers is 10 to 15 mm

when you push the belt in the middle to-

gether.

2.5.7 Controlling the clutch

You have to control the clutch at the same

time when you control the belt. When the

belt is removed you must control the outer

barrel. Clean the V-groove, if necessary.

When the shoe is battered, the power trans-

mission will be bad and the belt will slip.

2.5.8 Transport

For the transport of short ways you can use

the wheels of the machine. For long ways

you have to pack the handle and the safety

rack separately to safe place. Then you have

to place it on a transport vehicle where you

also have to fix the machine.

2.5.9 Refuelling

The machine is run by unleaded petrol.

Ensure yourself that no particles get into

the fuel tank when refuelling, so always

use a filter.

Use unleaded petrol because it is better for

the environment than leaded ones.

2.5.10 Cleaning

Clean the machine from dust, etc …

Clean the machine housing with a wet cloth

and a mild cleaning solution.

IM PORT AN T

Der Einsatz von Lösungsmitteln,

aggressiven Chemikalien oder

Scheuermitteln führt zu Sach-

schäden an der Maschine!

Daher gilt: Bei der Reinigung nur

Wasser und ggf. milde Reinigungsmit-

tel verwenden!

2.5.11 Cleaning the spark plug (Fig. I)

Take off the spark plug cap (Fig. F). Loosen

and remove the spark plug. Clean it with a

small brush from soot debris.

The contact distance shall account approx. 0,

5mm or ~ credit card thickness.

Engine

base

Oil plug

Dipstick

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Zipper ZI-RPE60 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 1,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Zipper ZI-RPE60 Manual

Product: