Manual Zibro LC 300 (page 9 of 135) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

728820

Zoom out

Zoom in

1/135

H: The TIMER indicator

light indicates that the

timer function has been

switched on.

E SETTING THE REQUIRED TEMPERATURE

The temperature setting can only be adjusted, when the heater is burning. Use

the adjustment keys N to adjust the temperature. First press either of the two

keys to switch on the function (the °C mark K will start blinking). Next, adjust the

temperature using the key on the right (Mmin.) to set the temperature to a higher

setting and the key on the left (Nhour) to lower the temperature. Press once to

increase the value one step. After approximately 10 seconds the °C mark will stop

blinking and the setting will be locked (Fig. G).

The available temperature settings range from 6°C minimum to 28°C maximum.

When the heater has been unplugged (or after a power failure), the temperature

will reset to the factory setting of 20°C.

F USING THE TIMER

The timer allows you to switch on the heater automatically at a preset time.

In order to switch on the timer, the correct time must have been set (refer to

Section C) and the heater should be off. Follow the procedure below:

1 Press the

button L and then the TIMER key O immediately after that.

The TIMER lamp  and the 4-digit K will start blinking.

2 Use the adjustment keys N to set the time at which the heater must ignite.

Use the key on the left (Nhour) to set the hours and the key on the right

(Mmin.) to set the minutes (interval of 5 minutes).

3 After approximately 10 seconds the 4-digit will show CLOCK again and the

TIMER lamp  will light up, indicating that the timer function has been

activated (Fig. H).

4 The timer will ensure that the room will have been heated to approximately

the required temperature at the set time.

When you want to switch off the heater and ignite it again with the timer, all

you have to do is press the TIMER key (refer to Section G).

Press the button L once to clear the timer setting.

G SWITCHING OFF THE HEATER

There are two ways to switch off the heater:

1 Press the button L. The information display will show the CLOCK

signal. Within approximately one minute the flame will have extinguished.

2 Press the TIMER key O, when you want to switch off the heater and ignite it

again with the timer the next time. This not only switches off the heater, but

it also activates the timer function. You can change the required time with

the adjustment keys N (refer to Section F).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Zibro LC 300 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 17,59 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Zibro LC 300 Manual

Product: