Manual Zibro LC 300 (page 8 of 135) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

728820

Zoom out

Zoom in

1/135

G: The required tempe-

rature on the left, the

measured temperature

on the right.

F: When the 4-digit

stops blinking, the set-

ting has been locked to

the indicated value.

B FILLING FUEL

Fill the removable tank in a suitable place since there can always be some

spillage. Follow the procedure below:

1 Make sure that the heater is switched off.

2 Open the upper lid and lift the removable tank out of the heater (Fig. B).

Put down the removable tank (cap pointing upwards, handle on floor) and

screw off the fuel cap (Fig. C).

NOTE: Some drops may leak from the tank.

3 Fill the removable tank using a fuel pump (refer to fuel pump operation

instructions.) Make sure that it is in a higher position than the removable tank

(Fig. D). Insert the ribbed hose into the opening of the removable tank.

4 Check the removable tank fuel gauge while filling the tank (Fig. E). Stop

filling once the gauge indicates that the tank is full. Never overfill the tank,

especially not when the fuel is very cold (fuel expands when it heats up).

5 Let the remaining fuel in the pump flow back into the jerrycan and carefully

remove the pump. Carefully screw the fuel cap back on the tank. Clean off

any spilled fuel.

6 Check whether the fuel cap is straight and tightened properly. Reinstall the

removable tank in the heater (cap down). Close the lid.

C SETTING THE CLOCK

It is only possible to set the correct time, when the heater is connected to the

mains and not burning. Use the adjustment keys N to set the time. First press

either of the two keys to switch on the function (the 4-digit K will start blinking).

Next, set the hours using the key on the left (Nhour) and the minutes using the

key on the right (Mmin.). Press once to increase the value by one step. When you

hold down the key, the value will continue going up, until you release the key

again. After approximately 10 seconds the 4-digit will stop blinking and the set-

ting will be locked (Fig. F). 5 minutes after switching off the heater, the informa-

tion on the display will disappear and the heater will automatically switch into the

stand-by position.

When the heater has been unplugged (or after a power failure), the time needs

to be set again.

D IGNITING THE HEATER

When used for the first time, a new heater may give out a smell for a short while.

You should therefore provide extra ventilation.

Always ignite the heater with the

button L

. Never use matches or a

cigarette lighter.

Just press the button L to ignite the heater. The POWER lamp will start blinking,

indicating that the ignition procedure has started. This will take a short while.

Once the heater is burning, the POWER lamp will remain lit (red). The information

display K will show two numbers. The light next to them indicates that these

numbers refer to the temperatures (Fig. G). The actual room temperature is

indicated below ROOM, while the temperature setting is indicated below SET. The

latter can be changed with the adjustment keys (refer to Section E).

Prior to igniting the heater, always check for sufficient fuel in the removable tank.

empty full

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Zibro LC 300 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 17,59 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Zibro LC 300 Manual

Product: