538960
77
Zoom out
Zoom in
Previous page
1/82
Next page
81MM1000-002_v01
Do not obstruct the ventilation openings in the housing
during operation.
Do not place the appliance on a soft surface.
Do not immerse the appliance drive unit in water and
do not wash it under running water.
Do not wash accessories when mounted on the
drive unit. Do not use abrasive cleaning agents such
as emulsions, creams, pastes, etc. for cleaning the
appliance housing. They may remove graphical
symbols, such as scales, markings, warning signs, etc.
Hint
Information on the product and hints on its use
Unplug the appliance after you nish using it. Put away
the cord, pushing it gently through the opening and
place the plug in the compartment.
If the appliance cannot be switched on, bring it to
a service centre.
Separate the meat to be minced from bones, sinews,
gristles and veins.
Cut large portions of the product into smaller pieces
before mincing.
Do not grind dry poppy seed. The poppy seed must
be scalded and soaked for dozen or so hours before
mincing.
Use a soft brush for cleaning the metal parts.
Do not wash the metal parts in dishwashers. Abrasive
detergents used in dishwashers may cause the metal
parts to become dark. Wash them manually using
traditional washing-up liquids.
TYPES OF ZELMER MINCERS
The table below shows a range of accessories available for the mincers and covered by this user manual.
Type
Accessories
Mincer unit No. 8 Shredder Juicer Burr grinder
MM1000.80
MM1000.82
MM1000.83
MM1000.84
MM1000.88
– basic accessories, – additional accessories available in shops
Technical data
The technical parameters are given on the rating plate of the
product.
Maximum time of non-stop operation: 10 minutes
An interval between repeated operation: 30 minutes
Noise level (L
WA
): 77 dB(A)
The appliance is built in insulation class II and does not
require earthing.
ZELMER mincers meet the requirements of the applicable
standards.
The appliance complies with the requirements of the
following directives:
Low Voltage Directive (LVD) – 2006/95/EC.
Electromagnetic Compatibility (EMC) – 2004/108/EC.
The product is marked with CE symbol on the rating plate.
Appliance description (Fig. A)
The foodstuff mincer consists of:
1
Drive unit – each drive unit is designed to work with each
mincing unit and shredder manufactured by ZELMER.
There are ventilation openings in the rear cavity of the
MM1000 drive unit compartment.
Mincer unit consisting of:
2
Mincer body
3
Feed screw with attached coupling
4
Knife
5
Screen with 4 mm holes
6
Threaded ring
7
Tray
8
Pusher
77


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zelmer MM1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zelmer MM1000 in the language / languages: English, Polish as an attachment in your email.

The manual is 3,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info