517530
23
Zoom out
Zoom in
Previous page
1/36
Next page
23
User’s manual
EN
0900 (9684)
10:00 11:30 16:00 17:30
Battery 2.3Ah
10:00 17:00
1200 (12912)
10:00 12:00 16:00 18:00
Battery 2.3Ah
10:00 20:00
1500 (16140) 10:00 12:00 16:00 19:00
2000 (21520) 08:00 21:00
2500 (26900) 08:00 22:30
3000 (32280) 07:00 23:30
SECONDARY AREAS – PROGRAMMING MODE
If the area to mow requires secondary areas based on the de nition given in the chapter “Preparation and Marking the Boundaries of the
Work Areas” then it is necessary to program the secondary areas so the robot knows how to reach the secondary area and at what frequency.
SECONDARY AREA 1 : Function for de ning the automatic mowing of a secondary area.
-
Percentage: Allows setting the dimensions of the secondary area to
mow in respect to the entire lawn surface. Below is a table to use as a
reference for con guring a secondary area:
20% Indicates a very small area.
30% Indicates an area which is approximately one third of the entire
garden.
50% Indicates an area which is approximately half of the entire
garden.
80% Indicates a secondary area which is bigger than the primary
area.
100%. The robot will follow the perimeter wire to mow the secondary
area each time it exits the charging station.
primary area
clockwise directionanti-clockwise direction
secondary area 1 (30%)
secondary area 2 (20%)
-
Distance: This allows setting the distance necessary for the robot to reach the secondary area by following the perimeter wire. It is
recommended to measure half the distance of the secondary area to ensure that the robot starts working inside that area.
-
Direction: Indicates the shortest direction for reaching the secondary area. The direction can be clockwise or anti-clockwise. The robot exits
from the charging station and follows the wire in the indicated direction to reach the secondary area.
SECONDAY AREA 2: Function for de ning the automatic mowing of secondary area number 2. This setting uses the same con guration
parameters as those used for secondary area 1.
SECONDAY AREA 3: (only for some versions, see “Technical Speci cations”). Function for de ning the automatic mowing of secondary area
number 3. This setting uses the same con guration parameters as those used for secondary area 1.
SAFETY – PROGRAMMING MODE
CHANGE PASSWORD: function for setting or changing the password.
-
No: the password does not need to be changed.
-
Yes: for entering or changing the password which will be used to start the robot and disable the alarm. You will prompted to enter the
following information :
Password: Enter the old password (manufacturer’s default 0000).
New password: Enter the new password.
Repeat password: Enter the new password again.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ZCS 9L2BL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ZCS 9L2BL in the language / languages: English as an attachment in your email.

The manual is 10,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ZCS 9L2BL

ZCS 9L2BL User Manual - Dutch - 56 pages

ZCS 9L2BL User Manual - Dutch - 33 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info