517530
22
Zoom out
Zoom in
Previous page
1/36
Next page
22
User’s manual
EN
REMOTE CONTROL: (only for some versions, see “Technical Speci cations”).
Refer to the remote control/console instructions for the pairing procedure.
SOUND: Allows disabling the acoustic signal when the robot is in the charging station.
BACK TO RECHARGE: Allows selecting the method for returning the robot to the charging
station.
1. “Follow wire”. The robot returns to the charging station by positioning the wheels on
either side of the perimeter wire.
2. “Bounce on wire”. The robot will run along the perimeter wire, touching it every now
and again in a rebound movement, until it recognises the “Recall” to the charging
station. Refer to the “Installation” chapter.
DATE: Function for setting the date.
TIME: Function for setting solar or daylight saving time.
SCHEDULES – PROGRAMMING MODE
WEEK: function for programming the operating days of the robot during the week. The
cursor automatically positions itself under the letter “M” (Monday).
Setting all the days at 1111111 means that the robot will work every day. Setting “0000000”
means that the robot will not work on any day of the week.
-
Value 1 : Robot’s work day.
-
Value 0 : Robot’s rest day.
Important
To get the best out of the robot, it is recommended to program the robot
to work every day.
WORK SCHEDULE 1: Function for setting the rst time of the robot’s working day. The
cursor automatically positions itself in the area under the rst time (e.g. 10:00am to 1:00pm).
Set the time for the start and end of the work. Setting the time at “00:00 – 00:00” means that
the robot will not work during the rst working time. If the robot emits a beep and resets the
time when this is entered, it means there is an inconsistency with the time entered or with
the second working time.
WORK SCHEDULE 2: Function for setting the second time of the robot’s working day.
Important
If it is necessary to set secondary areas, then it is preferable to program
both working times in order to increase the mowing frequency of the area.
Important
Approximately 3.5 hours is needed to fully charge the battery. Therefore,
it is recommended to leave an interval of 4 hours between working time 1
and working time 2.
The setting of the time is essential for the robot’s proper functioning. Many parameters inl uence the setting of the working time, such as the
secondary areas, number of batteries, complexity of the lawn, type of grass, etc. Generally, the working hours must be increased slightly when
mowing gardens with secondary areas, with lots of obstacles and complicated areas. Below is a table with the indicative times for con guring the
robot on rst use. NB. Set all the weekdays at “1” – “Work Days.”
m² (ft²) Time 1 Time 2
0200 (2152) 10:00 11:00
0500 (3230)
10:00 12:00
Battery 2.3Ah
10:00 11:00 14:00 15:00
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ZCS 9L2BL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ZCS 9L2BL in the language / languages: English as an attachment in your email.

The manual is 10,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ZCS 9L2BL

ZCS 9L2BL User Manual - Dutch - 56 pages

ZCS 9L2BL User Manual - Dutch - 33 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info