517530
10
Zoom out
Zoom in
Previous page
1/36
Next page
10
User’s manual
EN
Operation of the robot. The robot must be able to easily nd the charging station at the end of the work cycle, which will also be the departure
point for a new work cycle and for reaching any other work areas (hereinafter referred to as the “Secondary Areas”).
Position the charging station according to these rules :
-
On level ground.
-
On compact and stable ground with good drainage.
-
Preferably in the largest area of the lawn.
-
In case of sprinklers, make sure the water jets are not directed inside the charging station.
-
Make sure the entrance of the charging station is positioned as shown in the gure so that the robot can enter it by following the perimeter
wire in a clockwise direction.
-
There must be a straight area of 200 cm (78.74 ") in front of the base.
The charging station must be well fastened to the ground. To prevent a small step from forming in front of the base, position a small piece of
fake grass at its entrance as prevention. Alternatively, remove part of the grassy surface and install the base ush with the grass.
The charging station is connected to the power supply-transmitter unit via a cord that must move away from the charging station on the outside
of the cutting area.
Position the power supply-transmitter unit according to the following
rules:
-
In a well-ventilated area protected against atmospheric agents and
direct sunlight.
-
Preferably inside your home, a garage or shed.
-
If positioned outdoors, make sure it is protected in a well-ventilated
box away from direct sunlight and water. Do not position in direct
contact with the ground or in humid environments.
-
Position it on the outside of the lawn and not inside.
-
Position it at least 200 cm (78.74 ") from the charging station.
-
Stretch out the excess cord going from the charging station to the
power supply-transmitter unit. Do not shorten or lengthen the cord.
NO NO
OK OK
NO NO
The incoming section of the wire must be straight and aligned
perpendicularly to the charging station by at least 200 cm (78.74 ")
and the outgoing section must move away from the charging station as
shown in the gure; this allows the correct re-entry of the robot.
power supply-transmitter unit
charging station
min height 160 cm
/ 63 "
min. distance
200 cm
/ 78,74 "
min. distance
200 cm
/ 78,74 "
perimeter wire
If the robot is installed next to an area which has another robot (by the
same or by a different manufacturer), then the power supply-transmitter
unit must be modi ed during installation so that the frequencies of the two
robots do not interfere with each other.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ZCS 9L2BL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ZCS 9L2BL in the language / languages: English as an attachment in your email.

The manual is 10,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ZCS 9L2BL

ZCS 9L2BL User Manual - Dutch - 56 pages

ZCS 9L2BL User Manual - Dutch - 33 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info