Manual Yukon Photon XT (page 6 of 32) (English, German, French, Italian, Spanish)

663733

Zoom out

Zoom in

1/32

VIDEO OUTPUT

The riflescope is equipped with a video output (7) designed to connect external recording devices and to transmit

video signal to monitors, TV sets etc.

џ Use the supplied cable to connect an external signal receiver to the video output (7).

џ Turn on the scope – image will appear on the external device. Please make sure the external device is in the AV

mode.

To record video, you can use video recorders such as Yukon MPR (#27041) / CVR640 (#17044) and others.

NOTE: it is not recommended to attach the CVR640 on the riflescope because the video recorder is not designed for

heavy shock resistance.

ACCESSORIES

The riflescope is fitted out with an additional Weaver rail (8) which allows you to attach accessories like:

џ IR Illuminators Pulsar-805/Pulsar-940/Pulsar- X850 (#79071/79076/79074)

џ Laser IR Illuminators Pulsar L-808S/Pulsar L-915 (#79072/79075)

MAINTENANCE AND STORAGE

џ The riflescope features IPX4 degree of protection (protected against splash water) but cannot be submerged in

water.

џ Attempts to disassemble or repair the scope will void the warranty!

џ Clean the scope's optical surfaces only if necessary, and use caution. First, remove (by blowing with a blower

brush or canned air) any dust or sand particles. Then proceed to clean by using camera/lens cleaning equipment

approved for use with multicoated lenses. Do not pour the solution directly onto the lens!

џ The riflescope can be used in operating temperatures ranging from -15 °C...+50 °C. However, if it has been

brought indoors from cold temperatures, do not turn it on for 2 to 3 hours. This will prevent external optical surfaces

from fogging.

џ Always store the unit in its carrying case in a dry, well-ventilated space. For prolonged storage, remove the

batteries.

TROUBLESHOOTING

Listed below are some potential problems that may occur when using the scope. Carry out the recommended checks

and troubleshooting steps in the order listed. Please note that the table does not list all of the possible problems. If the

problem experienced with the scope is not listed, or if the suggested action meant to correct it does not resolve the

problem, please contact the manufacturer.

Next to the icon horizontal arrows appear, in the top right corner - location of the reticle along the X coordinate (see

pic.3).

Rotate the controller to move the reticle until it matches the point of impact.

First press of the controller enables vertical movement of the reticle (axis X appears on the

data panel), second press enables horizontal movement (icon Y). Initial position of the

reticle is in the centre of the display (coordinates X=0; Y=0). The field of view shows

positive and negative numbers which indicate movement relative to the coordinates “X=0;

Y=0”. Travel range of the reticle is +/-30 clicks horizontally and vertically.

Hold down the controller to save zeroing settings and to exit zeroing mode.

Take another shot - the point of impact should now coincide with the aiming point.

The scope should now be zeroed-in for the specified distance.

Note: each click equals to a 25mm/17 mm move of the reticle in the horizontal and vertical

plane at 100 m.

Pic.3

◄

►

X=+10

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Yukon Photon XT in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,76 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Yukon Photon XT Manual

Product: