663733

Yukon Photon XT Manual

5
Zoom out
Zoom in
Previous page
1/32
Next page
5
6
STARTING THE SCOPE AND IMAGE SETUP
џ Open the lens cap (9).
џ Short press on the button (4) to turn the riflescope on. The LED diode (3) will light up green.
Button (4) works as follows:
- Short press: riflescope is on, IR Illuminator is off;
- Another short press: riflescope is on, IR Illuminator is on – IR1 (power level I);
- Another short press: riflescope is on, IR Illuminator is on – IR2 (power level II);
- Another short press: riflescope is on, IR Illuminator is on – IR3 (power level III);
- Another short press: riflescope is on, IR Illuminator is off;
- Subsequent long press: riflescope is off, IR Illuminator is off.
IMPORTANT! When the indicator changes its colour to red, please replace the batteries.
џ Rotate the eyepiece adjustment ring (5) to see on the display a sharp image of the reticle.
џ Aim at a target 20-30 meters away.
џ Rotate the lens focus knob (10) to achieve quality image.
џ After this adjustment no further dioptre adjustment should be required, regardless of distance or other factors.
Adjust the image with the lens focus knob (10) only.
џ Rotate the controller (6) to adjust display brightness (icon ): clockwise – to increase brightness; counterclockwise
– to decrease brightness. Brightness adjustment range is from 0 to 15.
џ In low light conditions or in complete darkness turn on the built-in IR Illuminator (1) by pushing the “IR” (4) button.
Icon IR appears on the screen. IR power level changes as you sequentially press the button (4). Icon appears
when you turn off the IR Illuminator.
џ The built-in IR is not focusable.
џ Press and hold down the button (4) to turn off the riflescope.
MENU
Menu includes the following options:
џ Selection of pre-installed reticle.
џ Selection of reticle colour.
џ Zeroing the riflescope.
Selection of pre-installed reticle:
џ Press and hold down the controller (6) to enter the menu.
џ Rotate the controller to select icon . Press the controller to enter the submenu.
џ Rotate the controller to select the required reticle (6 types available). Its number is shown on the right of the icon.
Press the controller to confirm your choice.
џ To exit the menu, press and hold down the controller for two seconds. Or wait 10 seconds to exit automatically.
Selection of reticle colour:
џ Press and hold down the controller (6) to enter the menu.
џ Rotate the controller to select icon . Press the controller to enter the submenu.
џ Rotate the controller to select the required reticle colour (white (W), red (R) or green (G)). Press the controller to
confirm your choice.
џ To exit the menu, press and hold down the controller for one second. Or wait 10 seconds to exit automatically.
Zeroing the riflescope:
Bore sighting is a preliminary procedure to achieve proper alignment of the sight with the rifle's bore.
џ Mount the rifle with the riflescope installed on a bench rest.
џ Aim at a target 100 meters away.
џ Setup the riflescope according to the instructions in the section "STARTING THE SCOPE AND IMAGE SETUP”.
џ Aim the firearm at the target using the mechanical sight.
џ Using live ammunition, take a shot, continually aiming at the same hit point on the target.
џ Examine the target and determine if the aiming point coincides with the point of impact. Press and hold down the
controller (6) to enter the menu, rotate the controller to select icon .
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yukon Photon XT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yukon Photon XT in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info