540486
164
Zoom out
Zoom in
Previous page
1/174
Next page
<14. EXPLOSION PROTECTED TYPE INSTRUMENT>
14-13
IM 01F06A00-01EN
(2) Wiring
• Explosion proof
WARNING
All wiring shall comply with Canadian
Electrical Code Part I and Local Electrical
Codes.
In Hazardous locations, wiring shall be in
conduit as shown in the gure.
A SEAL SHALL BE INSTALLED WITHIN
50cm OF THE ENCLOSURE.
When the equipment is installed in Division
2, “FACTORY SEALED, CONDUIT SEAL
NOT REQUIRED”.
(3) Operation
• Explosion proof
WARNING
Note a warning label worded as follows.
Warning: OPEN CIRCUIT BEFORE
REMOVING COVER.
Take care not to generate mechanical
spark when access to the instrument and
peripheral devices in hazardous locations.
(4) Maintenance and Repair
WARNING
The instrument modi cation or part
replacements by other than authorized
representatives of Yokogawa Electric
Corporation are prohibited and will void CSA
Certi cation.
(5) Installation Diagram Intrinsically Safe
(and Note)
Intrinsically safe
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
+
-
+
[Remote type]
DYA (converter)
SUPPLY
PULSE
A
B
T (*1)
C
A
B
T
DY
(flowmeter)
SUPPLY
PULSE
Safety barriers
Safety barriers
[Integral type]
DY-N (flowmeter)
Hazardous Location
Group IIC, Zone 0
Class I, II, III, Division 1,
Groups A, B, C, D, E, F and G
Non Hazardous
Location
DYC: Signal cable
(*1) Wire for T terminal
With temperature sensor type : installed
Without temperature sensor type: not installed
F1409.ai
Electrical parameters of vortex flowmeter (DY) and vortex flow
converter (DYA).
Ui (Vmax)=30 V Ii (Imax)=165 mA Pi (Pmax)=0.9W
Ci=12 nF Li=0.15 mH
Installation requirements between flowmeter, converter and
Safety Barrier
Uo Ui Io Ii Po Pi Co Ci+Ccable
Lo Li+Lcable
Voc Vmax Isc Imax Ca Ci+Ccable
La Li+Lcable
Uo, Io, Po, Co, Lo, Voc, Isc, Ca and La are parameters of
barrier.
WARNING
In any safety barrier used output current
must be limited by a resistor ‘R’ such that
Io=Uo/R or Isc=Voc/R.
The safety barrier must be CSA certi ed.
Input voltage of the safety barrier must be
less than 250Vrms/Vdc.
Installation should be in accordance with
Canadian Electrical Code Part I.
Dust-tight conduit seal must be used when
installed in class II and III environments.
Do not alter drawing without authorization
from CSA.
164


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yokogawa DYA Vortex Flow Converter at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yokogawa DYA Vortex Flow Converter in the language / languages: English as an attachment in your email.

The manual is 5,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info