779822
11
Zoom out
Zoom in
Previous page
1/12
Next page
18 19
GB GB
Reversing or replacing the blades
WARNING!
Ensure the Robotic Mower is completely shut off before cleaning, adjusting or
replacing the blades. Always wear protective gloves.
WARNING!
To ensure maximum cutting efficiency and safety, always use recommended
replacement blades and blade mounting parts when replacing.
Your Robotic Mower has three blades, fixed to the blades disk.
Unless damaged by hard obstacles, these blades can last for up to five months of everyday use.
Weekly inspection of the blades and the fixing screws is advised. Note that the blades are double-
edged. When the first side becomes blunt, loosen the fixing screw and the blade upside down and
re-fix. Check that the blade can move freely.
A set of spare blades is included with the Robotic Mower. More blades can be purchased via
customer support.
To ensure you get the best performance from your machine, always replace all three blades at the
same time. Only use spare parts recommended by manufacturer.
NOTE: if blades have been removed/ changed, please ensure that the screw is firmly
secured in place and that the blade is free to move
Spare parts list
In case you need spare parts or any support with your device, please call our after sales centre.
Troubleshooting
Robotic Mower cannot dock with docking station
Check that the boundary wire in front and underneath the charger is in a straight line.
Check that the docking station's position is suitable as explained in this manual.
Robotic Mower runs in circles while mowing or while following
boundary wire back to docking station
Verify that no power cable runs parallel and in close proximity the boundary wire. If necessary,
reposition the boundary wire.
Check if a front wheel is stuck.
If a neighbor has a similar Robotic Mower, the signals may interfere. Try setting your docking
station and Robotic Mower are set to the alternative boundary signal S1 to S2.
Driving motor may be damaged, please contact customer support.
The Robotic Mower is noisy
Inspect the blade fixing screws; tighten if necessary.
Inspect the blades for damage; replace if necessary.
Grass may be too high. Try increasing the cutting height, or mow the lawn with an ordinary
lawnmower first.
Cutting motor failure, please call after sales service.
Mower remains at or returns to docking station when pressing START
button
Check if the mower has already completed the programmed working time for that day.
Battery is low, the Robotic Mower needs to be charged.
LED signal indicator on docking station
S1/S2 indicator lights on.
Boundary wire signal in good condition.
S1/S2 indicator flashes.
Boundary wire broken, no signal.
S1/S2 indicator flashing alternately.
Mower is charging in the docking station.
S1 S2
S1 S2
S1 S2
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yardforce NX 60i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yardforce NX 60i in the language / languages: English as an attachment in your email.

The manual is 8.86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info