689861
314
Zoom out
Zoom in
Previous page
1/363
Next page
Chapter 8 Part A Electrical system (XV535 models)
8A-11
17.1a The handlebar switches are held
together by screws (arrows); this is the
throttle side . . .
17.1b ... the clutch side switches are also
held together by screws (arrows)
17.1c Separate the switch halves for
access to the individual switches
18.5a Loosen the small screw (arrow) and disconnect the wire;
remove the three mounting screws ...
18.5b ... and take the switch out of the engine; replace the O-
ring with a new one
17 Handlebar switches - removal and installation
Refer to illustrations 17.1a, 17.1b and 17.1c
1 The handlebar switches are composed of two halves that clamp
around the bars. They are easily removed for cleaning or inspection by
taking out the clamp screws and pulling the switch halves away from
the handlebars (see illustrations).
2 To completely remove the switches, the electrical connectors in
the wiring harness should be unplugged.
3 When installing the switches, make sure the wiring harnesses are
properly routed to avoid pinching or stretching the wires.
18 Neutral switch - check and replacement
Check
1 Make sure the transmission is in neutral.
2 Remove the lower left frame cover (see Chapter 7). Locate the
switch harness (it has a single connector with sky blue wires), then
unplug the connector.
3 Connect the terminal in the harness side of the'connector to
ground/earth (bare metal on the motorcycle frame) with a short length
of wire.
a) If the light stays out, check the bulb and the wiring between the
ignition switch and neutral switch.
b) If the neutral indicator light comes on, the neutral switch may be
bad. Connect an ohmmeter between the terminal in the switch
side of the connector and ground. Shift through the gears. The
ohmmeter should indicate continuity (low resistance) in neutral
and no continuity (infinite resistance) in all other gears. If not,
replace the neutral switch.
Replacement
Refer to illustrations 18.5a and 18.5b
4 Remove the alternator cover (see Section 28).
5 Loosen the small screw on the switch and detach the wire (see
illustration). Remove the switch mounting screws and detach the
switch from the crankcase (see illustration). Remove the O-ring and
install a new one.
6 Installation is the reverse of the removal steps.
19 Sidestand switch - check and replacement
Check
1 Support the bike securely so it can't be knocked over during this
procedure.
2 . Follow the wiring harness from the switch to the connector, then
unplug the connector. Connect the leads of an ohmmeter to the wire
terminals. With the sidestand in the up position, there should be
continuity through the switch (little or no resistance).
314


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha XV920 Virago at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha XV920 Virago in the language / languages: English as an attachment in your email.

The manual is 52,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info